Abstract:A BNL type photoinjector was installed in HLS (Hefei Light Source) and commissioning work was carrying out in last months. The dark current was measured when the high power testing of the gun was processed. The quantum efficiency (QE) of the photocathode was measured and studied, the main parameters of beam quality such as electric charge, transverse emittance and energy were measured and presented in this paper. DESCRIPTION OF THE PHOTOINJECTOR The gun is a BNL type S-band normal conducting 1.6 cell cavity with copper cathode, which is nested in a compensation solenoid. The distance between the cathode and the edge of solenoid is 10cm. Fig.1 is the layout of the photoinjector in HLS. The YAG screens is used to imFigure 1: Layout of the photoinjector age the beam profile. Multi-slits is set at the distance of 55cm downstream from the cathode for transverse emittance measurement. The FCT and ICT are used to measure the current signal of the electron beam, the beam charge can be calculated by integrating the current signal. The energy measurement is achieved by a dipole and a YAG screen associate with a camera. As a key component of the system, the drive laser is consist of laser oscillator, regenerative amplifier and harmonic generation crystals. The laser pulse generated from the amplifier is 1047 nm wavelength, 8.3 ps (FWHM) pulse with 10 Hz repeat rate. Through the second and fourth harmonic generation crystals, 262 nm UV laser is gained. The performance of the laser system was measured and the optical transport line for oblique incidence at the cathode was also designed[1]. The high precise phase synchronization system is also a critical requirement for the normal operation of the injector. A timing stabilizer is used to synchronize the 102 MHz laser oscillator signal and the rf signal, the ∗Work supported by second phase of ”985” project † hezhg@mail.ustc.edu.cn precision is achieved about 100 fs . 2856 MHz signal is acquired by the 28th frequency multiplier and sent to the high power RF system. HIGH POWER TESTING OF THE GUN To get the gun into normal operation, conditioning work was done. After hundred hours continuous conditioning, almost 10 MW RF power at the exit of the klystron was achieved. Fig.2 showed the RF power at different high voltage settings of the power supply of the klystron. Figure 2: RF power at different high voltage settings Whereafter, the dark current was also measured, as shown in Fig.3. To collect all of the electron current, the magnetic field strength of the solenoid should be tuned with the changing of the RF power. Figure 3: Dark current Vs magnetic field strength of the solenoid at different RF power Proceedings of FEL2011, Shanghai, China WEPA01 FEL Technology ISBN 978-3-95450-117-5 331 C op yr ig ht c ○ 20 12 by th e re sp ec tiv e au th or s/ C C B Y 3. 0 — cc C re at iv e C om m on sA tt ri bu tio n 3. 0 (C C B Y 3. 0)

Primary Beam-Loading Tests on DC–SC Photoinjector at Peking University

BEAM LOADING TESTS ON DC-SC PHOTOINJECTOR AT PEKING UNIVERSITY

BEAM LOADING TESTS ON DC-SC PHOTOINJECTOR AT PEKING UNIVERSITY*

Experimental progress of DC-SC photoinjector at Peking university

Experimental Investigations of DC-SC Photoinjector at Peking University

Process of DC-SC Photoinjector

Stable Operation of the Dc-Srf Photoinjector

Updated Design of the DC-SC Photo-Injector at Peking University

Status of the dc-srf photoinjector for pku-setf

STUDY ON THE 3.5-CELL DC-SC PHOTO-INJECTOR*

Performance of Bialkali Photocathode in DC-SRF Photoinjector

Drive Laser System Of A High Average Current Photocathode Electron Gun In Pku

Drive laser system for the DC-SRF photoinjector at Peking University

THE DRIVE LASER SYSTEM FOR DC-SC INJECTOR

Development of DC-SRF Injector at Peking University

DC-SC INJECTOR FOR HIGH AVERAGE POWER FREE

Research and Fabrication of the Photocathode Used in DC-SC Photocathode RF Electron Gun

DC-SC INJECTOR FOR HIGH AVERAGE POWER FREE ∗

Commissioning of a Photoinjector in HLS

The High-Brightness Ultra-Short Pulsed Electron Beam Source at Peking University

Design Studies on a 500kv DC Gun Photo-Injector for the BXERL Test Facility