Abstract:While the addition of WC increases the hardness and wear resistance of coatings, an excessive WC content can also induce crack initiation and propagation, increasing brittleness and leading to premature failure. Therefore, in this study, WC particles were incorporated into nickel-based coatings by plasma-arc surfacing to optimize their content and distribution, balancing their tensile properties and wear resistance. The coatings were comprehensively evaluated through microstructural analysis, hardness testing, wear resistance assessment, and tensile testing. The results show that as the mass fraction of WC increased from 45% to 65%, the increase in carbon significantly promoted the formation of M7C3, M6C, and M23C6 carbides and suppressed the formation of the γ-phase. The microstructural analysis showed that the content of massive carbides increased significantly with the increasing WC content, and the XPS analysis further confirmed that the changes in the WC and Cr7C3 phases were particularly pronounced in the high-WC coating. The 65% WC coating showed higher hardness (a 232 increase in HV1.0), a lower and more stable coefficient of friction (0.42), and better wear resistance than the 45% WC coating, with a wear rate of 3.329 × 10−6 mm3/(N·m)−1, which was 3.709 × 10−6 mm3/(N·m)−1 lower than that of the 45% WC coating. The conventional tensile test results show that the maximum stress and strain of the 45% WC coating were 71% and 36% higher than those of the 65% WC coating, respectively. In addition, the 45% WC coating exhibited better ductility and quasi-cleavage characteristics, whereas the 65% WC coating showed typical brittle cracking behavior. The results of the field tensile tests also showed that the fracture time of the 65% WC coating was 27 s shorter than that of the 45% WC coating. Overall, the 45% WC coating had a good combination of strength and toughness.

A STUDY ON THE INFLUENCE OF WC ON WEAR RESISTANCE OF Ni-BASE SELF-FLUXING ALLOY

Influence of WC Content on Wear Resistance of Spraying-Welding Co/WC Coatings

Effect of Nanometer WC Powder on Wear Resistance of Thermal Spraying Coating

Optimizing Wear Resistance and Tensile Strength of Nickel-Based Coatings through Tungsten Carbide Reinforcement

Effect of Flame Conditions on Abrasive Wear Performance of Hvof Sprayed Nanostructured Wc-12co Coatings

Effects of WC mass fraction on microstructure and tribological behavior of plasma sprayed FeMnCoCr–WC coatings

Effect of WC-17Co Content on Microstructure, Mechanical Properties and Wear Resistance of WC-17Co/Ni Composites Produced with Cold Spraying

Wear Behavior of Plasma Sprayed Ni-WC Composite Coatings

Microstructure and wear behavior of WC-reinforced AlCoCrFeNiSi high entropy alloy coatings prepared by high-velocity arc spraying

Study on the abrasive resistance of Ni-based coatings containing WC hard phase

Erosion Resistance Of Ni-Wc Self-Fluxing Alloy Coating At High Temperature

Influence of nano-sized WC addition on the microstructure, residual stress, and tribological properties of WC-Co HVAF-sprayed coatings

Effect of WC addition on microstructure and properties of laser melting deposited Ti6Al4V

Influence of WC grain size on the microstructure and wear property enhancement of 18Ni300 coatings

Tribological Performance and Wear Mechanism of Laser Cladded NiCrAl-WC Coatings at High-Temperature

Effect of WC Addition on Microstructure and Tribological Properties of Bimodal Aluminum Composite Coatings Fabricated by Laser Surface Alloying

Microstructure and mechanical property of high velocity oxy-fuel sprayed WC-Cr3C2-Ni coatings

Rare Earth's Influence on Wear Resistance of Spray-melted Coatings with Mixture of Ni60B and 35Mass.%wc

Friction and wear behavior of Ni-based alloy coatings with different amount of WC–TiC ceramic particles

Effect of ingredients proportions on mechanical properties in laser-coated WC-blend welds

Effect of WC on microstructure, molten pool and properties of Ni based coatings by multi-layer laser cladding