Abstract:When the hypersonic aircraft cruises, the surface will generate huge aerodynamic heating. Aiming at the thermal protection of hypersonic aircraft, this paper presented a study on the thermal–hydraulic and thermodynamic performance of discrete inclined ribs enhanced bend tube based on the designed "Diamond" channel. Meanwhile, a comprehensive numerical investigation was carried out for different models. The fluid velocity was found to vary in the range of 0.1–3.5 m·s −1 , with the corresponding Reynolds number ranging from 3600 to 127000. The inlet temperature of heat transfer fluid was set to 253 K. It was visible that double–symmetrical longitudinal swirl was generated under a single upper and lower arrangement (Model D), which led to the best cooling performance on the inner wall. The performance evaluation criteria ( PEC ) and efficiency evaluation criterion ( EEC ) reached 0.99–1.18 and 0.66–1.00, respectively. The effect of four geometrical parameters (height–width ratio( H/d ), length–width ratio ( L/d ), group number of ribs ( n ), and tilt angle ( α )) of which the ranges are 0.5–2.5, 1.0–4.0,6–15 and 0°–90°, separately, was explored. The results showed that the inner wall temperature decreased up to 4.4 K when the Reynolds number was 72000. The Nusselt number and friction factor increased about 9.9 %–28.8 % and 16.5 %–111.5 %. Efficiency evaluation criterion reached 0.43–0.96. It was found that the combination of parameters would significantly affect the distribution of longitudinal swirls under the influence of secondary circulation in the bend tube. Moreover, many pairs of small vortices near the wall could improve active thermal protection performance. After obtaining the fitting function through the artificial neural network (ANN), the genetic algorithm (GA) was applied to obtain the Pareto front. The design variable for the L/d = 3.19, n = 11, and α = 14.3° was selected as the optimal solution by the TOPSIS method. When Reynolds number is 72000, the corresponding T in and ΔP were 261.86 K and 2471.2 Pa. The performance evaluation criteria and efficiency evaluation criterion reached 1.02 and 1.09, respectively. Furthermore, a design variable for the L/d = 3.0, n = 11, and α = 15° was given for ease of engineering. The present work verified the feasibility of realizing heat transfer enhancement by combining the secondary circulation with longitudinal swirls formed by bend tube and discrete inclined ribs and proposed a new design scheme of active cooling thermal protection systems (ACTPS).

Turbulent flow and heat transfer in discrete double inclined ribs tube

THE OUTSIDE TUBE HEAT TRANSFER PERFORMANCE OF THE DISCRETE DOUBLE INCLINED RIBS TUBE

Tubes with Heat Transfer Property Intensified by Multi-longitudinal Vortices According to the Field Coordination Theory

Visualization of longitudinal vortex flow in an enhanced heat transfer tube

Numerical study of air-side performance of a finned flat tube heat exchanger with crossed discrete double inclined ribs

Effects of Geometrical Parameters on Heat Transfer Enhancement in V-Spirally Corrugated Tube

Internal Flow Analysis of a Heat Transfer Enhanced Tube with a Segmented Twisted Tape Insert

Experimental Study of Condensation Heat Transfer of R134a Inside the Micro-Fin Tubes at High Mass Flux

Field Synergy Optimization and Enhanced Heat Transfer by Multi-Longitudinal Vortexes Flow in Tube

Investigating Enhanced Convection Heat Transfer in 3D Micro-Ribbed Tubes Using Inverse Problem Techniques

Thermohydraulic analysis of hybrid smooth and spirally corrugated tubes

Numerical analysis of buoyancy effect and heat transfer enhancement in flow of supercritical water through internally ribbed tubes

Experimental study on single-phase heat transfer performance of internal helically finned tubes covering low Reynolds number in turbulent flow

Turbulent flow and heat transfer in a new type of internally torsion-ribbed helical tube

Experimental and numerical investigation on the flow and heat transfer characteristics of the tube with an integrated internal longitudinal fin

Numerical Study of Thermal-Hydraulic Performance Improvement of Enhanced Surface Tubes

Numerical–Theoretical Analysis of Heat Transfer, Pressure Drop, and Fouling in Internal Helically Ribbed Tubes of Different Geometries

Experimental and Numerical Investigation of Heat Transfer Inside Two-Pass Rib Roughened Duct (AR = 1:2) under Rotating and Stationary Conditions

Enhancement Mechanisms for Single-Phase Turbulent Heat Transfer in Micro-Fin Tubes

Heat Transfer and Fluid Flow Characteristics of Microchannel with Discrete Double Inclined Ribs on Sidewalls

Design and optimization study of discrete inclined ribs enhanced bend tube based on "Diamond" active cooling thermal protection systems of hypersonic aircraft