Abstract:Organic photovoltaic solar cells can offer advantages of being mechanically flexible and durable, large area devices, lightweight, made from a diversity of materials and low-cost fabrication. Their efficiency is, however, still too low for commercial exploitation. Empirical observations reveal that polymer–fullerene (P3HT:PCBM) based solar cell performance depends on thermal annealing processes employed, especially the annealing temperatures and durations. The annealing parameters are known to influence the energetics and kinetics of the blending process or morphology, but the associated physics is not fully understood. In this work, current density–voltage characteristics of P3HT:PCBM bulk heterojunction organic solar cells, thermally annealed at different temperatures, 65–160 °C post fabrication, were investigated under dark and illuminated conditions, and compared to their as-cast counterparts. In certain electrical regimes, as-cast devices showed higher values of current density in comparison to the corresponding annealed devices. Such performance was attributed to air-borne chemical doping of the as-cast semiconductor layer, which creates electrically conductive percolation pathways within the as-cast devices. We propose that annealing of semiconductors must be a two-step process, which first initiates decrease in conductivity, followed by its increase. As-cast devices P3HT–PCBM bulk heterojunction solar cells prepared under atmospheric conditions were observed to have comparatively superior photovoltaic performance in comparison to thermally annealed devices. The efficiency drop in the annealed counterparts is attributed to dedoping due to thermal annealing. An annealing temperature of ~ 140 °C was found to be optimum for power conversion efficiency in the bulk heterojunction, 1:1 by mass, P3HT:PCBM based solar cells.

Nanoscale Morphology of High-Performance Polymer Solar Cells.

3-D Nanoscale Organization of Bulk Heterojunction Polymer Solar Cells

Nanoscale Structural and Electronic Evolution for Increased Efficiency in Polymer Solar Cells Monitored by Electric Scanning Probe Microscopy

CONTROLLING THE 3D NANOSCALE ORGANIZATION OF BULK HETEROJUNCTION POLYMER SOLAR CELLS

Three-Dimensional Nanoscale Organization of Bulk Heterojunction Polymer Solar Cells

Post-Fabrication Annealing Effects in Polymer-Nanotube Photovoltaic Cells

Correlating Nanoscale Morphology with Device Performance in Conventional and Inverted PffBT4T-20D:PC71 BM Polymer Solar Cells

Poly(3-hexylthiophene) Nanofiber Networks for Enhancing the Morphology Stability of Polymer Solar Cells

Correlating Nanoscale Morphology with Device Performance in Conventional and Inverted PffBT4T-2OD:PC<sub>71</sub>BM Polymer Solar Cells

Nanoscale control of the network morphology of high efficiency polymer fullerene solar cells by the use of high material concentration in the liquid phase

Thermally Stable, Efficient Polymer Solar Cells with Nanoscale Control of the Interpenetrating Network Morphology

Quantitative Nanoscale Monitoring the Effect of Annealing Process on the Morphology and Optical Properties of Poly(3-Hexylthiophene)/[6,6]-phenyl C61-butyric Acid Methyl Ester Thin Film Used in Photovoltaic Devices

Nanoscale Phase-Aggregation-induced Performance Improvement of Polymer Solar Cells.

Dark and illuminated J(V) characteristics of thin layered bulk heterojunction P3HT:PCBM sandwich solar cells after thermal treatment

Scanning Near-Field And Confocal Raman Microscopic Investigation Of P3ht-Pcbm Systems For Solar Cell Applications

Tuning Nanoscale Morphology Using Mixed Solvents and Solvent Vapor Treatment for High Performance Polymer Solar Cells

P3HT/PCBM Bulk Heterojunction Solar Cells: Impact of Blend Composition and 3D Morphology on Device Performance

Investigation of nanoscale morphological changes in organic photovoltaics during solvent vapor annealing

Effect of Crystalline Microstructure on the Photophysical Performance of Polymer/Perylene Composite Films

Self-assembly of well-defined poly(3-hexylthiophene) nanostructures toward the structure-property relationship determination of polymer solar cells

3D Structural Model of High-Performance Non-Fullerene Polymer Solar Cells As Revealed by High-Resolution AFM