Abstract:Organic photovoltaic solar cells can offer advantages of being mechanically flexible and durable, large area devices, lightweight, made from a diversity of materials and low-cost fabrication. Their efficiency is, however, still too low for commercial exploitation. Empirical observations reveal that polymer–fullerene (P3HT:PCBM) based solar cell performance depends on thermal annealing processes employed, especially the annealing temperatures and durations. The annealing parameters are known to influence the energetics and kinetics of the blending process or morphology, but the associated physics is not fully understood. In this work, current density–voltage characteristics of P3HT:PCBM bulk heterojunction organic solar cells, thermally annealed at different temperatures, 65–160 °C post fabrication, were investigated under dark and illuminated conditions, and compared to their as-cast counterparts. In certain electrical regimes, as-cast devices showed higher values of current density in comparison to the corresponding annealed devices. Such performance was attributed to air-borne chemical doping of the as-cast semiconductor layer, which creates electrically conductive percolation pathways within the as-cast devices. We propose that annealing of semiconductors must be a two-step process, which first initiates decrease in conductivity, followed by its increase. As-cast devices P3HT–PCBM bulk heterojunction solar cells prepared under atmospheric conditions were observed to have comparatively superior photovoltaic performance in comparison to thermally annealed devices. The efficiency drop in the annealed counterparts is attributed to dedoping due to thermal annealing. An annealing temperature of ~ 140 °C was found to be optimum for power conversion efficiency in the bulk heterojunction, 1:1 by mass, P3HT:PCBM based solar cells.

3-D Nanoscale Organization of Bulk Heterojunction Polymer Solar Cells

Three-Dimensional Nanoscale Organization of Bulk Heterojunction Polymer Solar Cells

CONTROLLING THE 3D NANOSCALE ORGANIZATION OF BULK HETEROJUNCTION POLYMER SOLAR CELLS

Three-dimensional Nanoscale Organization of Polymer Solar Cells

P3HT/PCBM Bulk Heterojunction Solar Cells: Impact of Blend Composition and 3D Morphology on Device Performance

Nanoscale Morphology of High-Performance Polymer Solar Cells.

Nanoscale Structural and Electronic Evolution for Increased Efficiency in Polymer Solar Cells Monitored by Electric Scanning Probe Microscopy

Nanoscale control of the network morphology of high efficiency polymer fullerene solar cells by the use of high material concentration in the liquid phase

Dark and illuminated J(V) characteristics of thin layered bulk heterojunction P3HT:PCBM sandwich solar cells after thermal treatment

Scanning Near-Field And Confocal Raman Microscopic Investigation Of P3ht-Pcbm Systems For Solar Cell Applications

Three-dimensional nano-networked P3MT/PCBM solar cells.

Tuning Nanoscale Morphology Using Mixed Solvents and Solvent Vapor Treatment for High Performance Polymer Solar Cells

Correlating Nanoscale Morphology with Device Performance in Conventional and Inverted PffBT4T-20D:PC71 BM Polymer Solar Cells

3D Structural Model of High-Performance Non-Fullerene Polymer Solar Cells As Revealed by High-Resolution AFM

Correlating Nanoscale Morphology with Device Performance in Conventional and Inverted PffBT4T-2OD:PC<sub>71</sub>BM Polymer Solar Cells

The effect of three-dimensional morphology on the efficiency of hybrid polymer solar cells

High Performance All-Polymer Solar Cells by Synergistic Effects of Fine-Tuned Crystallinity and Solvent Annealing.

Ternary Polymer Solar Cells Based on Two Highly Efficient Fullerene Acceptors with High Efficiency and Stability under Long-Time Thermal Annealing Treatment

Influence of thermal annealing on microstructure, energetic landscape and device performance of P3HT: PCBM-based organic solar cells

High Efficiency Polymer Solar Cells Based on Poly(3-Hexylthiophene)/indene-c70 Bisadduct with Solvent Additive

Solvent vapor-induced self assembly and its influence on optoelectronic conversion of poly(3-nexylthiophene): Methanofullerene bulk heterojunction photovoltaic cells