Abstract:To extend the service life of 316L stainless steel components in harsh environments, this study utilized laser cladding technology to enhance the hardness, wear resistance, and corrosion resistance of the 316L stainless steel surface. Nickel-based and cobalt-based cladding layers were prepared on the surface of the 316L stainless steel, and the microstructure and phases of the layers were analyzed using scanning electron microscopy, energy dispersive spectroscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. In addition, the hardness of the substrate and the cladding layers was tested with a microhardness tester, the frictional wear performance was tested with a pin on disc wear tester, and the corrosion resistance was tested with an electrochemical workstation. The experimental results indicate that the nickel-based cladding layer primarily comprises the γ-(Fe, Ni), Cr7C3, and Ni3Si phases, with equiaxed and dendritic grains being the predominant morphologies. By contrast, the cobalt-based cladding layer mainly comprises the γ-Co, Cr7C3, and Co7W6 phases, with columnar and dendritic grains being the predominant morphologies. Both cladding layers displayed a significantly better microhardness, wear resistance, and corrosion resistance than the substrate. Between the two cladding layers, the nickel-based cladding layer demonstrated a superior microhardness, whereas the cobalt-based cladding layer slightly outperformed in wear resistance and corrosion resistance. The findings from our results are important for understanding the performance of laser-cladding layers and laying a scientific basis for the promotion and optimization of laser cladding technology in industrial applications. Moreover, our results showed that laser cladding technology is increasingly important in extending the service life of components and improving the material performance.

Microstructures and Properties of Laser Cladding Stellite6/WC

Microstructural evolution in high power laser cladding of Stellite 6+WC layers

Microstructure Evolution of Stellite 6+wc by High Power Laser Cladding

Laser Cladding Stellite 6 + WC

Community organizers and (bio)filmmaking.

Microstructure and tribological properties of Stellite 12 coating by laser cladding on 304 stainless steel surface

Microstructure, hardness and slurry erosion-wear behaviors of high-speed laser cladding Stellite 6 coatings prepared by the inside-beam powder feeding method

Effect of Y2O3 Content on Microstructure and Wear Resistance of Laser Cladding Layer of Stellite-6 Alloy

Preparation of WC/Co Powders by Electroless Plating and Its Coating on 2cr13 Stainless Steel by Laser Cladding

High Power Laser Cladding Stellite 6+wc with Various Volume Rate by Duel Powder Feeding

Microstructure and corrosion-wear behaviors for laser cladding repaired martensitic stainless steels using Co-based and Ni-based powders

Microstructure, oxidation resistance and mechanical properties of stellite 12 composite coating doped with submicron TiC/B4C by laser cladding

Effect of Preheating Temperature on Geometry and Mechanical Properties of Laser Cladding-Based Stellite 6/WC Coating

Effect of Rare Earth Y Addition on the Microstructure and Properties of Stellite6/WC Coating by Laser Cladding

Cracking Mechanisms and Prevention of Stellite 6# Surface Layer Built by Laser Cladding During Thermal Cyclic Process

The Microstructure and Properties of Laser-Cladded Ni-Based and Co-Based Alloys on 316L Stainless Steel

Numerical and experimental investigation into temperature field and profile of Stellite6 formed by ultrasonic vibration-assisted laser cladding

WC-304 Powder/Screen Laser Composite Cladding Process and Simulation Research

Study on the microstructure and wear resistance of laser cladding layer of Ni and Cr on the surface of stainless steel

Microstructure evolution and wear resistance of laser cladded 316L stainless steel reinforced with in-situ VC-Cr7C3

Experimental Research on Cracking Behavior During High-Power CO 2 Laser Cladding