Abstract:Abstract Nickel-based alloy coatings were widely used for the remanufacturing of dies and moulds by laser cladding, but the crack sensitivity would be increase due to the higher strength and hardness, which reduced the wear resistance of Ni-based alloys. In this paper, Ni-based coatings with the addition of a plastic phase (an austenitic stainless net) were prepared using laser cladding technology, and the CeO 2 was added in cladding layers. The cracking mechanism, microhardness, microstructure, phase composition, and wear properties were investigated. The relationship between thermal stress and the elastic and plastic fracture had been developed from the standpoint of fracture mechanics and thermal elastic fracture mechanics. The fracture criterion of the nickel-based coating was obtained, and the study has shown that the crack sensitivity could be reduced by decreasing the thermal expansion coefficient Δ α . Thus, a new method was proposed, which the stainless steel nets were prefabricated on the substrate. It was found that the number of cracks reduced significantly with the addition of stainless steel net. When the stainless steel net with 14 mesh was added in Ni-based coatings, the average microhardness of nickel composite coating was 565 HV 0.2 , which was 2.6 times higher than that of the 45 steel substrate. Although the rare earth oxide 4 wt.% CeO 2 and stainless steel net were added in the Ni-based coating reducing the microhardness (the average microhardness is 425 HV 0.2 ), the wear resistance of it improved substantially. The wear volume of Ni-based composite coating was 0.56×10 −5 mm 3 ·N −1 ·m −1 , which was 85.1% lower than that of 45 steel. The experiment results have shown that the Nickel-based composite coating is equipped with low crack sensitivity and high abrasive resistance with austenitic stainless net and the rare earth oxide 4 wt.% CeO 2 . This research offers an efficient solution to produce components with low crack susceptibility and high wear-resistance coatings fabricated by laser cladding.

Study on the microstructure and wear resistance of laser cladding layer of Ni and Cr on the surface of stainless steel

The Microstructure and Properties of Laser-Cladded Ni-Based and Co-Based Alloys on 316L Stainless Steel

A Comprehensive Study on Microstructure and Wear Behavior of Nano-WC Reinforced Ni60 Laser Coating on 17-4PH Stainless Steel

The microstructure evolving and element transport of Ni-based laser-cladding layer in supercritical water

Microstructure and corrosion-wear behaviors for laser cladding repaired martensitic stainless steels using Co-based and Ni-based powders

Study of Cracking Mechanism and Wear Resistance in Laser Cladding Coating of Ni-based Alloy

Study on Microstructure and Properties of Nickel-Based Self-Lubricating Coating by Laser Cladding

Study on the microstructure and heat affected zone of nickel-based alloy cladding layer

Microstructure and Wear Resistance of Ductile Cast Iron Laser Clad with Ni-Ti-Co-C

Microstructure evolution and wear resistance of laser cladded 316L stainless steel reinforced with in-situ VC-Cr7C3

Microstructure and tribological properties of Stellite 12 coating by laser cladding on 304 stainless steel surface

Microstructure evolution and high-temperature tribological behavior of Ti3SiC2 reinforced Ni60 composite coatings on 304 stainless steel by laser cladding

Properties of Laser-Clad Stainless Steel–Ni/WC Double-Layer Coatings

TiC-Reinforced Austenitic Stainless Steel Laser Cladding Layer on 27SiMn Steel Surface: A Comparative Study of Microstructure, Corrosion, Hardness, and Wear Performance

Wear resistance of nickel-based alloy coating formed by multilayer laser cladding

Study on microstructure and wear behaviors of MoS2/TiC/Ni composite wear-resistant coating by laser cladding

Microstructure, Phase Constituents and Wear Behavior of Fe/Ni-based Laser Clad Layers

Microstructure and Wear Resistance of Laser Cladding of Fe-Based Alloy Coatings in Different Areas of Cladding Layer

Microstructure, microhardness and corrosion resistance of laser cladding Al2O3@Ni composite coating on 304 stainless steel

Effect of Substrate Material Properties on Microstructure and Mechanical Properties of Ni60 Coatings Prepared by Extreme High‐Speed Laser Cladding

Microstructure formation, corrosion properties, and tribological properties of laser-cladded CrCoNi medium-entropy alloy coatings