Abstract:To ascertain the influence of SiC nanowires on sintering kinetics of heterophase ceramics, two composite powders (TaSi2-TaC-SiC and TaSi2-TaC-SiC-SiCnanowire) are fabricated by mechanically activated combustion synthesis of Ta-Si-C and Ta-Si-C-(C2F4) reactive mixtures. Remarkable compressibility is achieved for the TaSi2-TaC-SiC-SiCnanowire composition (green density up to 84% as compared with 45.2% achieved for TaSi2-SiC-TaC) which is attributed to the lubricating effect of residual adsorbed fluorinated carbon (most likely C4F8). The outcomes of pressureless sintering of TaSi2-TaC-SiC and TaSi2-TaC-SiC-SiCnanowire compositions are vastly different; the former experiences no significant densification or grain growth and does not attain structural integrity, whereas the latter achieves relative density up to 93% and hardness up to 11 GPa. The SiC nanowires are not retained in consolidated ceramics, but instead, act as a sintering aid and promote densification and grain growth. Sintering mechanisms of TaSi2-TaC-SiC and TaSi2-TaC-SiC-SiCnanowire powders are analyzed using thermodynamic and ab initio grand potential calculations, as well as the analysis of grain size versus relative density relations. In the case of solid-state sintering, the densification and grain growth in heterophase non-oxide ceramics are governed by the same mechanisms as previously investigated single-phase oxides. The presence of SiC nanowires enhances grain-boundary related diffusion processes due to the high specific surface and aspect ratio of the nanowires. At 1500 °C, where the formation of the transient Si-based liquid phase is thermodynamically viable, only the SiC nanowire-containing composition demonstrated the intense grain coarsening and densification associated with liquid-assisted sintering. This effect can be attributed both to the presence of SiC nanowires and purification of residual oxide impurities due to C2F4-activated combustion synthesis employed for the in situ formation of SiC nanowires.

The Effect of Diluent on Combustion Synthesis of Si3n4-Sic-Tin Ceramics with Small Diameter

Study on the Combustion Synthesis of Si3N4-SiC-TiN Ceramics

EFFECT OF DILUENT CONTENT ON Si_3N_4-SiC-TiN CERAMICS PREPARED BY SELF-PROPAGATION HIGH-TEMPERATURE SYNTHESIS

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Effect of the Diluent on Combustion Synthesis of Silicon Nitride

Effect of nitrogen pressure on combustion synthesis of Si3N4-SiC-TiN ceramic

The Combustion Synthesis Of Si3n4-Tin-Sic Multiphase Ceramics

MICROSTRUCTURE OF Si3N4-TiN-SiC CERAMICS DURING COMBUSTION SYNTHESIS PROCESS

Effects of Pelletization of Reactants and Diluents on the Combustion Synthesis of Si3N4 Powder

Reaction Mechanisms of Combustion Synthesis of Si<sub>3</sub>N<sub>4</sub> -Sic -Tin Ceramics

Effects of Si Source and High Gravity on Combustion Synthesis of Ti3sic2 in Air

Reaction Mechanisms of Combustion Synthesis of Si<sub>3</sub>N<sub>4</sub> -SiC -TiN Ceramics

Reaction mechanisms of combustion synthesis of Si3N4 -SiC -TiN ceramics

Effect of In Situ Grown SiC Nanowires on the Pressureless Sintering of Heterophase Ceramics TaSi2-TaC-SiC

Effects of Nitrogen Pressure and Diluent Content on the Morphology of Gel-Cast-foam-assisted Combustion Synthesis of Elongated Β-Si3n4 Particles

Combustion Synthesis Of Tin Ceramic Powder And Parts

Effects of diazenedicarboxamide additive on the content of α-Si3N4 synthesized by combustion method

Combustion synthesis of high flexural strength, low linear shrinkage and machinable porous β-Si3N4 ceramics

On the Progress of Combustion Synthesis of Si3n4 Ceramic: from Laboratory Research to Industrial Production

On the Progress of Combustion Synthesis of Si<sub>3</sub>N<sub>4</sub> Ceramic: From Laboratory Research to Industrial Production

Effects Of Carbon Addition On Densification And Mechanical Properties Of Porous Si3n4 Ceramics