Abstract:Features peculiar to the synthesis of SiC–Si 3 N 4 –Si 2 N 2 O composite powder with a controlled content of silicon carbide, nitride, and oxynitride phases, as well as the structure and properties of hot-pressed ceramics produced from this powder, were examined. The optimal composition of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O powder was achieved by heating a 1 : 3 mixture of thermally expanded graphite (TEG) and silicon up to 1200°C in air. The interaction of TEG with fine silicon at 1200°C led to the formation of a solid solution of carbon in silicon carbide, accompanied by heat release. The generated heat increased temperature within localized volumes of the TEG cellular structure to a level where air nitrogen facilitated the development of silicon nitride and oxynitride and an amorphous phase. The amorphous phase crystallized as the interaction time increased to 2.5 h. The duration of the process influenced the final distribution of the phases, formed with the participation of CO, SiO, and air nitrogen. The microstructure of the synthesized powder was characterized by a general agglomerated state, resulting from rod and plate forms of Si 3 N 4 and Si 2 N 2 O. Hot pressing of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O composite powder with Al 2 O 3 and Y 2 O 3 activators yielded superfine ceramics, possessing enhanced hardness and fracture toughness (HV10 = 20.7 GPa and K Ic = 6.5 MPa · m 1/2 ). The structure of the ceramics sintered at 2000°C differed from those sintered at 1850°C, primarily by higher density and average grain size. The superfine state significantly influenced the abrasive wear resistance of the ceramics in dry friction conditions. The linear wear index of a sample with an average size of structural elements varying from 0.2 to 1.5 μm was 111 μm/km at a sliding speed of 1 m/sec under a load of 0.2 MPa. This was significantly lower than the linear wear index of industrial ceramics of reaction-sintered silicon carbide (RSSC), which was 232.4 μm/km.

In-situ hot pressing/solid-liquid reaction synthesis of dense titanium silicon carbide bulk ceramics

Synthesis and Mechanical Properties of In-Situ Hot-Pressed Ti3SiC2 Polycrystals

Synthesis of High-Purity Ti3SiC2 Polycrystals by Hot-Pressing of the Elemental Powders

Enhanced Mechanical/electrical Properties of in Situ Synthesized SiC-TiB2 Ceramic Composites by Reactive Hot-Pressing Sintering

Novel (Zr, Ti)B2-(Zr, Ti)C-SiC ceramics via reactive hot pressing

Novel (Zr, Ti)(C, N)–SiC ceramics via reactive hot-pressing at low temperature

Synthesis and Consolidation of Composite Materials in the SiC–Si3N4–Si2N2O System

Novel TiC-based ceramic with enhanced mechanical properties by reaction hot-pressing at low temperature

Fabrication of highly dense Ti3SiC2 ceramics by pressureless sintering of mechanically alloyed elemental powders

Fabrication, Microstructure, and Properties of SiC/Al 4 SiC 4 Multiphase Ceramics Via an In-Situ Formed Liquid Phase Sintering

Novel (ti, W)C–SiC–WSi2 Ceramics Fabricated Via in Situ Reaction Spark Plasma Sintering at 1600 °C

Fabrication, microstructure, and properties of SiC/Al4SiC4 multiphase ceramics via an in-situ formed liquid phase sintering

Enhanced Performance in Si3N4 Ceramics Cutting Tool Materials by Tailoring of Phase Composition and Hot-Pressing Temperature

Synthesis of Ti<sub>3</sub>SiC<sub>2</sub> Bulk Materials with B<sub>2</sub>O<sub>3</sub> Additive

Synthesis of Ti3SiC2 Bulk Materials with B2O3 Additive

Solid–liquid Reaction Synthesis of Layered Machinable Ti3AlC2 Ceramic

Microstructure characterization and mechanical properties of in situ synthesized Ti2(Al,Si)C reinforced Al composites

Reactive Synthesis of Polycrystalline Ti3AlC2 and Its Sintering Behavior

In-situ reaction syntheis and mechanical properties of ultra high temperture ceramics

Preparation and Sinterability of Submicron Titanium Carbide Powders Synthesized with Phenolic Resin As Carbon Source by Carbothermal Reduction

Preparation of Al2O3/Ti3SiC2 multilayer materials by in-situ synthesis