Abstract:To ascertain the influence of SiC nanowires on sintering kinetics of heterophase ceramics, two composite powders (TaSi2-TaC-SiC and TaSi2-TaC-SiC-SiCnanowire) are fabricated by mechanically activated combustion synthesis of Ta-Si-C and Ta-Si-C-(C2F4) reactive mixtures. Remarkable compressibility is achieved for the TaSi2-TaC-SiC-SiCnanowire composition (green density up to 84% as compared with 45.2% achieved for TaSi2-SiC-TaC) which is attributed to the lubricating effect of residual adsorbed fluorinated carbon (most likely C4F8). The outcomes of pressureless sintering of TaSi2-TaC-SiC and TaSi2-TaC-SiC-SiCnanowire compositions are vastly different; the former experiences no significant densification or grain growth and does not attain structural integrity, whereas the latter achieves relative density up to 93% and hardness up to 11 GPa. The SiC nanowires are not retained in consolidated ceramics, but instead, act as a sintering aid and promote densification and grain growth. Sintering mechanisms of TaSi2-TaC-SiC and TaSi2-TaC-SiC-SiCnanowire powders are analyzed using thermodynamic and ab initio grand potential calculations, as well as the analysis of grain size versus relative density relations. In the case of solid-state sintering, the densification and grain growth in heterophase non-oxide ceramics are governed by the same mechanisms as previously investigated single-phase oxides. The presence of SiC nanowires enhances grain-boundary related diffusion processes due to the high specific surface and aspect ratio of the nanowires. At 1500 °C, where the formation of the transient Si-based liquid phase is thermodynamically viable, only the SiC nanowire-containing composition demonstrated the intense grain coarsening and densification associated with liquid-assisted sintering. This effect can be attributed both to the presence of SiC nanowires and purification of residual oxide impurities due to C2F4-activated combustion synthesis employed for the in situ formation of SiC nanowires.

Novel (ti, W)C–SiC–WSi2 Ceramics Fabricated Via in Situ Reaction Spark Plasma Sintering at 1600 °C

Processing and mechanical properties of B4C-SiCw ceramics densified by spark plasma sintering

Fabrication, Microstructure, and Properties of SiC/Al 4 SiC 4 Multiphase Ceramics Via an In-Situ Formed Liquid Phase Sintering

Fabrication, microstructure, and properties of SiC/Al4SiC4 multiphase ceramics via an in-situ formed liquid phase sintering

Microstructure and Mechanical Properties of the Spark Plasma Sintered Tac/Sic Composites: Effects of Sintering Temperatures

Combined effect of SiC and carbon on sintering kinetics, microstructure and mechanical properties of fine-grained binderless tungsten carbide

Densification and microstructure evolution of W-TiC-Y2O3 during spark plasma sintering

Densification and Enhancement of Sic Particulate Reinforced Fine Grain Sic Ceramic

The microstructure and deformation behavior of W-SiC composites via spark plasma sintering

Densification, Microstructures, and Mechanical Properties of (zr, Ti)(C, N) Ceramics Fabricated by Spark Plasma Sintering

Microstructure and properties of nano-laminated Y3Si2C2 ceramics fabricated via in situ reaction by spark plasma sintering

Novel (Zr, Ti)(C, N)–SiC ceramics via reactive hot-pressing at low temperature

Structure and Properties of Spark Plasma Sintered SiC Ceramics with Oxide Additives

Microstructure and Mechanical Properties of Hot-Pressed Sic/(W, Ti)C Ceramic Composites

The effects of SiC addition on the sintering densification, phases, microstructure and mechanical properties of W

Effect of In Situ Grown SiC Nanowires on the Pressureless Sintering of Heterophase Ceramics TaSi2-TaC-SiC

Microstructures and mechanical properties of in-situ SiC-TiB2 ceramic composites fabricated by reactive melt infiltration

Enhanced Mechanical/electrical Properties of in Situ Synthesized SiC-TiB2 Ceramic Composites by Reactive Hot-Pressing Sintering

Effect of Tungsten Carbide on Densification and Mechanical Properties of Silicon Nitride Ceramics by Spark Plasma Sintering

Processing and Characterization of SiB0.5C1.5N0.5 Produced by Mechanical Alloying and Subsequent Spark Plasma Sintering

Microstructure and Mechanical Properties of Porous SiC Ceramics by Carbothermal Reduction and Subsequent Recrystallization Sintering