Abstract:Bi2Te3-based compounds are currently the most commercially relevant thermoelectric materials near room temperature. They are prepared via hot pressing, hot deformation, spark plasma sintering, and other consolidation processes, which are typically performed at 400–500 °C. Such high-temperature processes are energy-intensive and generate unnecessary waste heat, making them undesirable for a large-scale production. In this study, a low-temperature liquid-phase-assisted sintering (or so-called cold-sintering) process was employed to fabricate p-type Bi0.5Sb1.5Te3 bulk materials at temperatures below 150 °C. At the optimal sintering temperature (130 °C), a ZT value as high as 0.56 at 450 K can be achieved, competitive to that of a commercial Bi0.5Sb1.5Te3 ingot (ZT 0.8–1.0). The addition of a small amount of transient liquid facilitates grain reorientation and expedites a mass transfer process under axial compaction and liquid evaporation conditions, thus resulting in nearly fully densified Bi0.5Sb1.5Te3 pellet samples (>97% theoretical density). Furthermore, the low-temperature sintering process results in the reduction of grain size and promotes twin boundaries, resulting in a low lattice thermal conductivity of 0.57 W m–1 K–1 at 380 K due to phonon scattering. The strategy reported in this work can be used not only as a substitute for high-temperature sintering of other thermoelectric materials but also to engineer phonon scattering for high-performance thermoelectrics.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.1c03540.Single parabolic band model and calculated transport properties; EBSD analysis for pellet sintered at 110 °C; BSE, EDS mapping, and TEM images of pellet sintered at 130 °C; average ZT values; and XPS results (PDF)This article has not yet been cited by other publications.

Synthesis and properties of rare earth containing Bi2Te3 based thermoelectric alloys

Solvothermal synthesis and thermoelectric properties of lanthanum contained Bi–Te and Bi–Se–Te alloys

Solvothermal Synthesis and Characterization of Nano-Structured La-Bi-Te Thermoelectric Materials

Improved Thermoelectric Properties of Bi2Te3−xSexalloys by Melt Spinning and Resistance Pressing Sintering

Flower-like nanostructure and thermoelectric properties of hydrothermally synthesized La-containing Bi2Te3 based alloys

Synthesis and Thermoelectric Properties of Bi2te3 Based Nanocomposites

Solvothermal synthesis of nanostructured Bi_2Te_3 based thermoelectric materials

Tunable Electrical Conductivity and Simultaneously Enhanced Thermoelectric and Mechanical Properties in n-type Bi<sub>2</sub>Te<sub>3</sub>

Tunable Electrical Conductivity and Simultaneously Enhanced Thermoelectric and Mechanical Properties in n‐type Bi2Te3

Structures and Electric Properties of Bi2Te3 Based Alloys Prepared by Solvothermal Synthesis

Novel thermoelectric Bi2Te3 nanotubes and nanocapsules prepared by hydrothermal synthesis

Development of Nanostructured Bi2Te3 with High Thermoelectric Performance by Scalable Synthesis and Microstructure Manipulations

Sonochemical Synthesis of Nanocrystalline Bi2Te3 Thermoelectric Compounds

Cold-Sintered Bi 2 Te 3 -Based Materials for Engineering Nanograined Thermoelectrics

Thermoelectric Properties of Hydrothermal Synthesized Bi-Te-Se Alloys

Solvothermal Preparation and Thermoelectric Properties of Ternary Sn-Bi-Te Alloy

The reaction mechanism for the synthesis of Bi2Te3-based thermoelectric materials by aqueous chemical method

High-pressure synthesis and thermoelectric performance of tellurium doped with bismuth

Rare Earth Element Doping Introduces Pores to Improve Thermoelectric Properties of p-Type Bi 0.46 Sb 1.54 Te 3

Nanostructuring and improved performance of ternary Bi–Sb–Te thermoelectric materials

Thermoelectric properties of hydrothermally synthesized and hot pressed n-type Bi2Te3 alloys with different contents of Te