Abstract:Effects of atmosphere, temperatures and duration time on the surface topography and the electrical conductivity of LiNbO3 single crystals deposited with a 300-nm-thick layer of different metal films (Al, Mg and Zn) had been systematically investigated. LiNbO3 samples covered with Al film annealed at 500 degrees C for 6 h in different atmosphere were firstly studied. There were a lot of small holes generated after the residual film cleaning. In addition, the surface roughness was enhanced with increasing pressure. Compared with areas that without metal Al coated, a sharp step was formed, especially the deep step of about 125 nm in 3%H-2 + Ar atmosphere. The I-V curves reveal that the electrical conductivity of sample surface annealed at normal pressure was better than that in low vacuum. The current value was up to about 20 mA at 10 V in 3%H-2 + Ar, resulting in the conductivity significantly improved. Subsequently, samples deposited with different metal (Zn, Mg and Al, respectively) films annealed at 400 degrees C for 6 h in 3%H-2 + Ar were discussed. After wet etching, interestingly, a large number of nano sized protrusions were formed on the surface. Both of samples coated with Mg and Zn films presented no obvious step depth, while a clear step about 13 nm was formed for Al-coated samples. The I-V curves show that the surface conductivity of Zn-coated samples achieved the maximum of about 2.5 mA at 5 V among the three metals. Furthermore, Zn-coated samples annealed at different temperatures and holding time in 3%H-2 + Ar were also analyzed. After pickling, also, there were a lot of nanobulges appeared across the surface. With the temperatures keeping growth and the time extending, the nanobulges became much more compact and well-distributed. At the same time, the surface conductivity of samples would be gradually and effectively enhanced. The PL and XPS spectrums have indicated that more oxygen vacancies formed with increasing temperatures and holding time, resulting in the significant improvement in surface conductivity. The conduction mechanisms of sample surface can behave differently owing to the various annealing conditions.

Preparation Of Linbo3 Thin Films By Pechini Method

LOW-TEMPERATURE PREPARATION OF NANO-CRYSTALLINE LITHIUM NIOBATE POWDERS BY THE POLYMERIC PRECURSOR METHOD

Synthesis of Stoichiometric Linbo3 Nanopowder Through A Wet Chemical Method

Preparation of Nano-Structured BaTiO3 Thin Film by Electrophoretic Deposition and Its Characterization

LiNbO3 Thin Films through a Sol–Gel/Spin-Coating Approach Using a Novel Heterobimetallic Lithium–Niobium Precursor

Pulsed Laser Deposition of Linbo3/Litao3 Multilayer Films on Sio2/Si(100) Substrate

Optical and Structural investigations of LiNbO3 thin films by PLD

Morphology Characterization and Mechanism Analysis of the Microstructure of Linbo3 Crystals Fabricated by Using Focused Ion Beam Milling

Preparation and Conducting Performance of Lanio3 Thin Film on Si Substrate

RESEARCH ON THE LiNbO3 THIN FILMS PREPARED BY SOL-GEL PROCESS

Chemical Solution Deposition Process and Characterization of Li and Ti Doped Nio Thin Films

Effects of Atmosphere, Metal Films, Temperatures and Holding Time on the Surface Topography and Electrical Conductivity of LiNbO3 Single Crystals

Pbtio3 Thin-Films Prepared By Metalorganic Chemical-Vapor-Deposition On Laalo3

Preparation and Characterization of Lithium-Ion-Conductive Li1.3al0.3ti1.7(Po4)(3) Thin Films by the Solution Deposition

Mocvd Growth and Properties of Zno Thin Films on Linbo3 Substrates

Microstructure of LiNbO3 Thin Films Grown on Silicon Substrates by Pulsed Laser Deposition

Fabrication of the preferentially orientated LiNbO3 nanoparticles and their ferroelectric behaviors

The preparation of and water adsorption on thin films of niobium oxide on Pt(111)

Fabricate and Characterize the Lithium Niobate Thin Films Prepared on Glass Substrate by Sol-gel Process

Growth Behavior of (pr2/3ca1/3)mno3 Layer and the Buffering Effect on Pb(Zr,Ti)O-3 Thin Films

Texture control of sol-gel derived Pb(Mg1/3Nb2/3 O3-PbTiO3 thin films using seeding layer