Abstract:Metal supported solid oxide fuel cells (MS-SOFC) possess several advantages like good mechanical property, easy assembling, fast start-up and capability to maintain redox stable due to fuel leakage. However, it has been a critical challenge to deposit cathode on the metal supported cell in the oxidizing atmosphere, which is mainly limited by the low calcination temperature yielding vulnerable electrolyte-electrode interface. The cathodes prepared in the protecting atmosphere are also not satisfied, instead it will increase the complexity of the cell fabrication process. Lower down the cathode deposition temperature using aqueous infiltration has become one of the optimized methods for MS-SOFC. Also, we have proposed an alternative way for the fabrication of metal supported single cell with robust cathode through whole cell reduction. Here, we present results of both above two approaches for the fabrication of nano-structured cathodes in MS-SOFC. The cells in this study are based on Fe-Ni (1:1 in mol ratio) support, Fe-Ni/YSZ anode and YSZ electrolyte prepared through tape-casting, thermal isostatic pressing and co-firing. As illustrated in the following schematic configuration, La0.6Sr0.4Co0.2Fe0.8O3-δ (LSCF) cathodes were deposited in the porous YSZ layer of the pre-reduced Ni-Fe|Ni-Fe-YSZ||YSZ||P-YSZ substrate by infiltration and fired at the cell operation temperature around 700 oC. A-site deficiency of ~4-8% was introduced into LSCF cathode and was expected to enhance the sintering activity of LSCF nano particles at low calcination temperature and to enhance the cathode performance by the excess cobalt and iron oxide at LSCF surface. As in the second approach, Sr0.95Ti0.3Fe0.63Ni0.07O3-δ – Gd0.1Ce0.9O1.95 (STFNi-GDC) graded cathode will be screen printed on the NiO-Fe2O3|NiO-Fe2O3-YSZ||YSZ|GDC substrate and fired at high temperature in air as normal cathode preparation procedure. Then the whole cell will be reduced in H2-Ar to obtain Fe-Ni alloy support and reduced STFNi cathode with in-situ exsolved (Fe,Ni) alloy nano particles anchored in the oxide surface. During the cell test, the reduced STFNi-(Fe,Ni) will be re-oxidized in air, forming the surface decorated iron and cobalt oxide particles, which were presumably to be expected to increase the cathode performance through improvement of oxygen surface exchange coefficient. Figure 1

Fabrication of Dense La0.7Ca0.3Cr0.97O3-δ Interconnect Thin Membrane on Composite Anode Support by Co-firing

Fabrication of Dense La0.7Ca0.3Cr0.97O3-delta Interconnect Thin Membrane on Composite Anode Support by Co-firing

Fabrication of dense La 0.7Ca 0.3 Cr 0.97O 3-δ interconnect membrane on novel SOFC composite support by co-firing

A simple and easy one-step fabrication of thin BaZr0.1Ce0.7Y0.2O3−δ electrolyte membrane for solid oxide fuel cells

Preparation and Performance of Tri-layer Composite Anode Supported Fuel Cell

Evaluation of simple, easily sintered La0.7Ca0.3Cr0.97 O3-δ perovskite oxide as novel interconnect material for solid oxide fuel cells

Fabrication and Optimization of La 0.4 Sr 0.6 Co 0.2 Fe 0.7 Nb 0.1 O 3- Δ Electrode for Symmetric Solid Oxide Fuel Cell with Zirconia Based Electrolyte

Performance and Optimization of Ni/3 Mol% Y2O3-ZrO2 Anode Supported SOFC

A Novel Co-firing Process for Multi-layers of Solid Oxide Fuel Cells

Improvement of Anode-Supported Solid Oxide Fuel Cells

Enhancing chemical stability and performance in proton-conducting solid oxide fuel cells through novel composite cathode design

Preparation, Evaluation, and Application of SUS430/441 Interconnect with Mn-Co Coating in Solid Oxide Fuel Cells

High Performance Composite Interconnect La0.7ca0.3cro3/20 Mol% Reo1.5 Doped Ceo2 (re = Sm, Gd, Y) for Solid Oxide Fuel Cells

Validation and Electrochemical Characterization of LSCF Cathode Deposition on Metal Supported SOFC

An Anode-Supported Micro-Tubular Solid Oxide Fuel Cell with Redox Stable Composite Cathode

Fabrication and Properties of Anode-Supported Solid Oxide Fuel Cell

Stability of Ni-YSZ Anode for SOFCs in Methane Fuel: the Effects of Infiltrating La0.8Sr0.2FeO3-δand Gd-Doped CeO2Materials

Conducting Property and Performance Evaluation of LNF As Cathode Current Contact Layer in Solid Oxide Fuel Cell

Electrochemical Property of Multi-Layer Anode Supported Solid Oxide Fuel Cell Fabricated Through Sequential Tape-Casting and Co-Firing

Fabrication and Characterization of La0.6Sr0.4Co0.2Fe0.8O3-δ-Yttria Stabilized Zirconia Composites Cathode Prepared by Infiltration Method

In-Situ Formation of Nano-Structured Cathode on Metal Supported SOFC