Application of SPC in Needle Punched Technology Process

Tian-ming XV,Rui MIAO

DOI: https://doi.org/10.3969/j.issn.1005-2054.2009.02.011

2009-01-01

Abstract:Take nonwovens weight quality control in traditional nonwovens industry for an example,analyse production process using SPC control technology.SPC Stat.methods and attentions in application for production line are discussed in the paper.

What problem does this paper attempt to address?

SPC application in the needle punched process

Xu Tianming,Miao Rui

DOI: https://doi.org/10.3969/j.issn.1004-7093.2009.07.007

2009-01-01

Abstract:Application of SPC technique to the industry of needle punched process which is described with traditional nonwoven production,taking roll weight control for an example,proper control method and notes in implementation were discussed in this paper.
Study on the Embedded SPC System Based on LAN

Yin Jianjun,Yu Zhonghua,Wu Zhaotong

DOI: https://doi.org/10.1108/15982688200300014

2003-01-01

Asian Journal on Quality

Abstract:Statistical Process Control (SPC) is recognized as one of the most important tool of quality control (QC), an is one research focus in order to implement SPC quickly and effectively using computer technology and network environments. This paper proposes the principle and topology of embedded SPC based on the Internet/Intranet, emphatically discusses the embedded data sampling block, embedded network interface and SPC strategy. An example of application is given.
State of Art in Quality Control Systems of Polymer Production Processes

WANG Fang,LIN Wen,WANG Jingdai,YANG Yongrong

DOI: https://doi.org/10.3321/j.issn:1000-6613.2006.01.003

2006-01-01

Abstract:For the polymer production industries,the competitive edge will come from the technology that excels in controlling the polymer quality in a consistent way over the entire plant.The state of the art quality control systems of polymer production plant is reviewed,with the main focus on on–line soft–sensing and optimal grade transition control problems.It is proposed that the most important factor in developing an intelligent quality control system is quality modeling and implementing plant–wide quality estimation and control is beneficial.Finally,some open problems and potential development trends of the field are pointed out.
Application of SPC in High Power Semiconductor Device Production

Zhang Zhi-yong

Abstract:Statistical Process Control(SPC) techniques are introduced to analyze process parameters in order to improve device reliability and yield,control process production and penetrate quality control into critical production process in this paptr.The SPC techniques consist of judgment rule,technique flow,control chart and process capability analysis aredetailed.Taken POCL3 diffusion for example,how SPC techniques work in high power semiconductor device process is shown.It is calculated that process capability index is 1.81,deviation is slight and practical distribution mean value is centered on the target mean value.It is concluded that the process ability is very strong.

Engineering
Field bus-based embedded SPC system

殷建军,余忠华,吴昭同

DOI: https://doi.org/10.3785/j.issn.1008-973X.2004.06.021

2004-01-01

Abstract:How to develop a new statistical process control (SPC) system in complicated modern manufacturing environment utilizing abundant information resources was discussed. To embed separate units in a sophisticated system, this paper proposed the principle, topology and overall solution of SPC system of hierarchy field bus-based quality control network at the level of plant and enterprise. The embedded SPC separate units were comprised of special modules designed for different simple functions. The structure of the field bus-based network, the interface of embedded industrial ethernet network, and the implementation of the control strategy of embedded SPC units were discussed, along with the principle of reliability and security. This system had characteristics of better environment flexibility, safety and credibility in practice, provides a basic plat roof for total quality control in manufacturing.
Application Of Embedded System Of Data Sampling To Quality Control

Jj Yin,W Jiang,Zh Yu,Zt Wu

2002-01-01

Abstract:The theory and technology of embedded system of data sampling based on industrial Ethernet is studied according to quality control during manufacturing, Grads criteria of dynamic measuring is advanced. At the same time, the theory and model of Network SPC based industries Intranet, strategy of SPC and CEWMA control chart are researched.
A High-precision Displacement Measuring System in SPC

Jianjun Yin,Zhonghua Yu,Zhaotong Wu

DOI: https://doi.org/10.3321/j.issn:0254-3087.2005.05.014

2005-01-01

Abstract:To solve the problems that companies usually face when using statistical process control (SPC) in the quality control. The main framework of high-precision displacement measuring system is proposed. The methods of system design and optimization based on LVDT sensor are given. The technologies of network and data stream protocol of system are also discussed. The performance of the measuring system is evaluated with measurement system analysis (MSA). The result shows that this measuring system has features of stability, high precision, low cost, large volume of data storage and network function, and so on, the system is worth popularizing for application.
Statistical control of the production process of rolled products

Krzysztof Knop

DOI: https://doi.org/10.30657/pea.2018.20.06

2018-09-01

Production Engineering Archives

Abstract:Abstract The article presents the results of the use of SPC tools, i.e. control charts and indicators of the qualitative capability to assess the stability and capability of the production process of rolled products - I-sections. Statistical analysis of the collected data regarding the selected feature of the analysed product - the width of the foot, and the normality of the distribution were done, which showed that the obtained distribution of measurement results is not a normal distribution. As a result, appropriate SPC procedures for non-normal distribution were used. The Pareto-Lorenzo diagram and FMEA method were also used to obtain information about the structure of non-conformities of the analysed product and the level of risk associated with them. This information was used to propose corrective actions and improve the production process of rolled products.
Design on Method of Statistical Process Control (SPC) Based on RFID Technology

Jiaqi Li,Qing Zhang,Bowei Li

2010-01-01

Abstract:In the application of Statistical Process Control (SPC), a traditional method in quality management, in order to ensure the accuracy of the data, we often copy the data in hand, manually calculate, and then dot. So it would be very time-consuming and labor-intensive. For this situation enhancement, enterprises have developed automatic data collection system and control charts analysis system with the high cost, and real-time control to the quality of the production process can not be achieved. In this paper, in order to combine automatic data collection and automatic control charts, the rapidly developing RFID technology is integrated into SPC. Automatic data collection and utilization of algorithms to determine quality of products are effective. By setting timers in RFID tags, a real-time effective control to quality of work pieces on production line could come true. At the same time, 12864 LCD (liquid crystal display) is introduced to SPC system, which is more convenient for producers to adjust the production process and wiser for managers to do production management. What is more important, it lays the foundation for the reform of the manufacturing sector.
A comparative study of physical properties of nonwoven fabrics produced by uni- and bi-directional needles using response surface methodology

Bahram Asri,Safdar Eskandarnejad,M. Bameni Moghadam

DOI: https://doi.org/10.1080/00405000.2024.2313902

IF: 1.7698

2024-02-15

Journal of the Textile Institute

Abstract:In the production of needle-punched nonwoven fabrics, the direction of needle barbs is towards the tip of the needle. When the needle penetrates into the fabric, the barbs carry some fibres into the fabric and when it returns the barbs are empty. This means that, the needle works when it penetrates into the fabric and doesn't work when it returns. Using a bi-directional barb needle in the needle-punch process was proposed as an idea with the theory that, the needle also works when returning (leaving the layer). This study investigates the physical properties of needle-punched nonwoven fabrics produced with unidirectional and bi-directional needle types. Effects of needle penetration depth (NPD), strokes per minute (SPM), and needle type (N 1 , N 2 ) on properties such as gram per square meter (GSM), thickness, fabric density (FD), and static puncture resistance (SPR) are examined. An experiment with 19 runs was designed using response surface methodology and optimal design with two quantitative factors, including NPD and SPM, and one qualitative factor containing needle types. In addition, four responses were measured and reported, including GSM, thickness, FD, and SPR. Test results show that needle N 2 produces a fabric with lower FD, higher GSM, thickness, and SPR in comparison to needle N 1 , and was selected in optimization process with a desirability value of 0.872 against 0.688 for needle N 1 . The improved fabric properties of needle N 2 may be exploited for the economic benefits of the nonwoven fabric producers or textile industry.

materials science, textiles
Intelligent Integrated Control Method in Manufacturing Process

Yang Musheng,Zhang Yu

DOI: https://doi.org/10.1109/ical.2007.4338835

2007-01-01

Abstract:EPC and SPC play a different role in manufacturing process quality control, EPC method can properly control single parameter's changes during the manufacturing process to meet quality requirements, SPC can predicts and control stability of manufacturing process and discovers the control state of manufacturing process as soon as possible. Therefore, using the SPC and EPC integrated control technology can better ensure the quality of the products. This paper outlines the features of the SPC and EPC method during the manufacturing quality control, putting forward a process control system which integrates the EPC and SPC method and studies the informational interface technique, the intelligent integration technique and the harmonious control technique for the two method, and then analyzes the integrated technique and the quality guaranteed technique for the two method through a specific manufacturing process example. The application of this technique not only guarantees the needs of the individual parameter, but also the distribution regulation of the group of a same parameter.
Intelligent Integrated Method of EPC and SPC in Manufacturing Process Quality Control

Yang Musheng,Zhang Yu

DOI: https://doi.org/10.1109/ICCA.2007.4376674

2008-01-01

Abstract:Although the EPC method can properly control single parameter's changes during the manufacturing process to meet quality requirements, however, in project practice, it has been proved that a single control parameter can not guarantee the best manufacturing quality. The manufacturing quality is also closely related with the distribution of the values of parameters. Therefore, using the SPC and EPC integrated control technology can better ensure the quality of the products. This paper outlines the features of the SPC and EPC method during the manufacturing quality control, putting forward a process control system which integrates the EPC and SPC method and studies the informational interface technique, the intelligent integration technique and the harmonious control technique for the two method, and then analyzes the integrated technique and the quality guaranteed technique for the two method through a specific manufacturing process example. The application of this technique not only guarantees the needs of the individual parameter, but also the distribution regulation of the group of a same parameter, so it may markedly improve the quality of the manufacturing process. Therefore, overall product quality is improved.
The Application of Spinning Craft in Muffler

JIA Zhi-xin,QIAO Run-e,JIN Yong

DOI: https://doi.org/10.3969/j.issn.1672-545X.2011.09.035

2011-01-01

Abstract:Spinning craft is a kind of fast,efficient successive partial plastic forming technology.This paper analyzes the hidden problems of quality in its traditional process,and based on the domestic and international industry conditions,the specific process and the advantages and disadvantages of spinning are also analyzed in detail.
Data transformation in SPC for semiconductor machinery control: A case of monitoring particles

M.-C. Chen *,C.-T. Su,C.-C. Hsu,Y.-W. Liu

DOI: https://doi.org/10.1080/00207540500070475

IF: 9.018

2005-07-01

International Journal of Production Research

Abstract:Yield is an important indicator of productivity in semiconductor manufacturing. In the complex manufacturing process, the particles on wafers inevitably cause defects, which may result in chip failure and thus reduce yield. Semiconductor manufacturers initially use wafer testing to control the machine for the number of particles. This machinery control procedure aims to detect any unusual condition of machines, reduce defects in actual wafer production and thus improve yield. In practice, the distribution of particles does not usually follow a Poisson distribution, which causes an overly high rate of false alarms in applying the c-chart. Consequently, the semiconductor machinery cannot be appropriately controlled by the number of particles on machines. This paper primarily combines data transformation with the control chart based on a Neyman type-A distribution to develop a machinery control procedure applicable to semiconductor machinery. The proposed approach monitors the number of particles on the testing wafer of machines. A semiconductor company in Taiwan in the Hsinchu Science Based Industrial Park demonstrated the feasibility of the proposed method through the implementation of several machines. The implementation results indicated that the occurrence of false alarms declined extensively from 20% to 4%.

engineering, manufacturing, industrial,operations research & management science
Process Monitoring Via Quality-Oriented Spc Under Information-Based Manufacturing

Yu Zhang,Musheng Yang,Zhimin Jia

DOI: https://doi.org/10.1109/ical.2008.4636443

2008-01-01

Abstract:Current SPC charts are process monitoring tools for keeping process in stable status, and can not assure a desired process quality without additional requirements. To develop a quality-oriented SPC approach, a standardized interface between process quality indices and the parameter design of control charts, i.e., quality-oriented statistical tolerance (QOST), is needed. QOST can be determined based on required process quality index (PQI) or process capability index (PCI). The guidelines of QOST to SPC control charts is actually to determine the permitted deviation of the center lines of SPC charts which is naturally formed by the actual data of process output. Theoretically, when SPC control charts are used to assure the process to be in controlled state and also to meet a predetermined PQI or PCI, it should satisfy the restrict condition representing by a given QOST. The procedures of this new SPC approach with a case study are given for process monitoring under information-based manufacturing.
Optimisation of punching parameters for enhanced filtration performance of non-woven by response surface methodology

Priyal Dixit,S. M. Ishtiaque

DOI: https://doi.org/10.1080/00405000.2023.2297473

IF: 1.7698

2024-01-06

Journal of the Textile Institute

Abstract:This work highlights the relevance of punch density, needle penetration depth and basis weight on the nonwoven fabric's properties. Fibre fineness-specific optimised carding parameters, that is feeder, cylinder and doffer speeds were used for the preparation of carded web to produce considered basis weight of carded batts. Fabric thickness, bursting strength, mean flow pore size, air permeability, air filtration efficiency and pressure drop were extensively investigated, and a relationship was developed using the Box–Behnken design. The punch density and needle penetration depth were optimised to achieve the required levels of mean flow pore size at constant basis weight for enhancing the air filtration behaviour of non-woven fabrics.

materials science, textiles
Study of the SPC Technology Application to the Laser Sculpture Process

高建峰,张猛,刘东

DOI: https://doi.org/10.3969/j.issn.1000-100x.2009.08.031

IF: 5.967

2009-01-01

IEEE Transactions on Power Electronics

Abstract:An example of statistical process control(SPC) technology application to the laser sculpture process and the machine in UHVDC research center of PERI is introduced.The abnormity or abnormal tendency is detected by SPC technology,then the reasons are found out and corresponding measures are taken in time,which makes the laser sculpture machine to resume normalization and to produce more products with high quality and reliability.In this aspect,effect is good.
SPD Technology for Fabricating Bulk Nanocrystalline Materials

ZHENG Zhijun,GAO Yan

DOI: https://doi.org/10.3321/j.issn:1005-023x.2008.01.022

2008-01-01

Abstract:The processing principle and classification of severe plastic deformation(SPD)for fabricating bulk nanocrystalline materials are summarized in the present paper.SPD technologies are commonly classified into severe plastic torsion straining(SPTS),equal channel angular pressing or extrusion(ECAP or ECAE)and multi forging ac- cording to the ultra-fining mechanism of processed materials.The shearing mechanism and technique parameters of SPTS and ECAP as well as their advantages and disadvantages are discussed.At the same time,some solutions are brought forward on the basis of above discussions.
Study on Quality Control of Integrated Method Based on STA/SPC/EPC

YANG Musheng,ZHANG Yu

DOI: https://doi.org/10.3969/j.issn.1001-3881.2011.07.004

2011-01-01

Abstract:Proved by engineering practice,invalidation of process can not be forecasted by engineering process control,and optimal manufacturing quality in the process can not be guaranteed.The features of STA,SPC and EPC were outlined during the manufacturing quality control,a process control system which integrated STA,EPC and SPC was put forward.The informational system interface technique,the intelligent integration technique and the harmonious control technique were studied.The integrated technique and the quality guaranteed technique were analyzed through a specific manufacturing process example.The results show that the application of this technique guarantees not only the need of individual parameter,but also the distribution regulation of the group of a same parameter.The quality of manufacturing process can be markedly improved.
Production Technology of the Spunbonded Nonwoven Fabric

ZHAO Bo

DOI: https://doi.org/10.3969/j.issn.1008-8261.2008.03.003

2008-01-01

Abstract:Briefly introduce the origin,process principle, process type, raw material, new technology and development direction of spunbonded nonwoven fabric technology. It is pointed out that the new-type spunbonded nonwoven facilities must have many advantages, such as high productivity, low energy consumption,good flexibility,strong adaptability,easy maintenance and products of quality.

Application of SPC in Needle Punched Technology Process

SPC application in the needle punched process

Study on the Embedded SPC System Based on LAN

State of Art in Quality Control Systems of Polymer Production Processes

Application of SPC in High Power Semiconductor Device Production

Field bus-based embedded SPC system

Application Of Embedded System Of Data Sampling To Quality Control

A High-precision Displacement Measuring System in SPC

Statistical control of the production process of rolled products

Design on Method of Statistical Process Control (SPC) Based on RFID Technology

A comparative study of physical properties of nonwoven fabrics produced by uni- and bi-directional needles using response surface methodology

Intelligent Integrated Control Method in Manufacturing Process

Intelligent Integrated Method of EPC and SPC in Manufacturing Process Quality Control

The Application of Spinning Craft in Muffler

Data transformation in SPC for semiconductor machinery control: A case of monitoring particles

Process Monitoring Via Quality-Oriented Spc Under Information-Based Manufacturing

Optimisation of punching parameters for enhanced filtration performance of non-woven by response surface methodology

Study of the SPC Technology Application to the Laser Sculpture Process

SPD Technology for Fabricating Bulk Nanocrystalline Materials

Study on Quality Control of Integrated Method Based on STA/SPC/EPC

Production Technology of the Spunbonded Nonwoven Fabric