Removal of Cr(VI) by hollow micron zero-valent iron in groundwater containing different ions: Mechanisms and mineralized products
Chunyang Gao,Bing Wang,Xingchun Li,Yuzhu Zhang,Tongxu Qu,Xianyuan Du,Jin Zheng,Jinguo Feng
DOI: https://doi.org/10.1016/j.psep.2023.02.072
2023-03-31
Process Safety and Environmental Protection: Transactions of the Institution of Chemical Engineers, Part B
Abstract:The development of zero-valent iron in-situ reactive zone technology is restricted by the poor mobility and reactivity of zero-valent iron. Hence,hollow micron zero-valent iron (H-mZVI) was prepared through rapid liquid reduction and used to remove Cr(VI) from aqueous solution. Scanning electron microscopy confirmed that H-mZVI had a hollow structure, particle size of approximately 1 μm, and rough surface. X-ray diffraction indicated that H-mZVI was mainly composed of ZVI. Brunauer–Emmett–Teller results showed that H-mZVI had a large specific surface area (25.54 m 2 /g) and pore volume (0.12 cm 3 /g). The Cr(VI) removal efficiency of H-mZVI was 6.18 times that of solid micron zero-valent iron (S-mZVI), and the removal reaction conformed to first-order reaction kinetics. Electrochemical test results revealed that the electron transport efficiency was stronger, Fe 2+ concentration in aqueous solution was larger, and the decrease in oxidation–reduction potential was more obvious in H-mZVI than in S-mZVI. Desorption experiment and X-ray photoelectron spectroscopy showed that H-mZVI removed Cr(VI) primarily through reduction and secondarily through adsorption. The effects of conventional ions and humic acid (HA) on Cr(VI) removal by H-mZVI were in the order of PO 4 3- >HA>NO 3 - >CO 3 2- >HCO 3 - >Cl - =Mg 2+= Ca 2+ . The corrosion products and their proportions varied in the presence of different ions. Graphical Download : Download high-res image (151KB) Download : Download full-size image Performance data from a geothermal power plant that uses a dry-type working fluid (n-Pentane) was evaluated. The experimental working conditions of the geothermal power plant were recorded. By using these recorded data the structural and parametrical optimisation of the plant was applied. As a structural modification, the probable performance of the plant was scrutinised by considering the integration of a superheater into the plant. For both present and structurally optimised cases, parametric optimisations were made as an operational modification. During the analyses, the high and low pressure Organic Rankine Cycles (ORCs) of the energy converter plant were optimised for varying turbine inlet temperatures and pressures. After comprehensive analyses, it was concluded that superheating the working fluid by structural modification (superheater integration) had a negative effect on the system performance. On the other hand, together with parametric analyses, a considerable improvement in system performance was obtained. For all cases and parametric values, the system was also evaluated in terms of environmental effect. Odor pollution has become one of the important environmental problems in China. In this study, Gas Chromatography Ion Mobility Spectrometry (GC-IMS), Gas Chromatography Mass Spectrometer (GC-MS) and Flame Ionization Detector (FID) were combined to obtain comprehensive information of the odor produced during the production of Captan, a common pesticide, and to evaluate the efficiency of the odorant treatment techniques utilized by the manufacturer studied. Based on our findings, refining, an important phase during the production process of Captan, was found to be the most important factor in determining the type and the concentration of the odorant produced. Of the odorants found during the production process, perchloromethylmercaptan (CCl 3 SCl) and other chlorine-containing compounds are the key odorants during the production process based on the calculation of odor activity value (OAV). The current odorant treatment utilized by the manufacturer studied showed about 40 % removal rate. However, the odorant treatment produced a new odorant, dimethyl disulfide. Therefore, a much more targeted odorant treatment technique without the production of new odorants is desired and should be utilized. Co-pyrolysis technology is an effective method to reduce heavy metal concentration in biochar produced from biosolids. In the current study, the effect of co-pyrolysis feedstock on product yield and properties was studied by mixing Biosolids (BS) with Wheat Straw (WS) and Canola Straw (CS) in a 3:1 mass ratio and carrying out thermal decomposition at 700 °C in a fluid bed reactor. This study found that the feedstock ash content and the volatile matter had a significant effect on biochar, oil, and gas yields from co-pyrolysis. The results also indicated that the addition of WS and CS feedst -Abstract Truncated-