Abstract:The effect of nitrogen content on the formation of an equiaxed solidification structure of Fe-16Cr steel was investigated. Moreover, two different kinds of refractory materials, i.e., alumina and magnesia, were employed to control the type of oxide inclusion. The characteristics of TiN(-oxide) inclusions were quantitatively analyzed in both molten steel and solidified samples. When the melting was carried out in the alumina refractory, the grain size continuously decreased with increasing nitrogen content. However, a minimum grain size was observed at a specific nitrogen content (approx. 150 ppm) when the steel was melted in the magnesia refractory. Most of the single TiN particles had a cuboidal shape and fine irregularly shaped particles were located along the grain boundary due to the microsegregation of Ti at the grain boundary during solidification. The type of TiN-oxide hybrid inclusion was strongly affected by the refractory material where Al2O3-TiN and MgAl2O4-TiN hybrid-type inclusions were obtained in the alumina and magnesia refractory experiments, respectively. The formation of oxide inclusions was well predicted by thermochemical computations and it was commonly found that oxide particles were initially formed, followed by the nucleation and growth of TiN. When the nitrogen content increased, the number density of TiN linearly increased in the alumina refractory experiments. However, the number of TiN exhibits a maximum at about [N] = 150 ppm, at which a minimum grain size was obtained in the magnesia refractory experiments. Therefore, the larger the number density of TiN, the smaller the primary grain size after solidification. The number density of TiN in the steel melted in the magnesia refractory was greater than that in the steel melted in the alumina refractory at given Ti and N contents, which was due to the lower planar lattice disregistry of MgAl2O4-TiN interface rather than that of Al2O3-TiN interface. When ∆TTiN (= difference between the TiN precipitation temperature and the liquidus of the steel) was 20 K to 40 K, the number density of effective TiN was maximized and thus, the grain size was minimized after solidification. Finally, although most of the TiN particles were smaller than 1 μm in the molten steel samples irrespective of the nitrogen content, TiN particles larger than 10 μm were observed in the solidified samples when the nitrogen content was greater than 150 ppm. The growth of TiN particles during melting and solidification was well predicted by the combinatorial simulation of the ‘Ostwald ripening model’ based on the Lifshitz–Slyozov–Wagner theory in conjunction with the ‘Diffusion controlled model’ using Ohnaka’s microsegregation equation.

Nitriding Simulation for Polycrystals of Grain Size Gradient

In-situ Measurement and Numerical Simulation of Nitriding Kinetics of Grain-Oriented Silicon Steel

Mass Transport in Laser Surface Nitriding Involving the Effect of High Temperature Gradient: Simulation and Experiment

Mathematical Modelling and Computer Simulation of Nitriding

Anisotropic Phase Transformation Mechanism on Coarse-Grained and Fine-Grained Pure Titanium at Low-Temperature Plasma Nitriding

Improved Nitrogen Transport in Surface Nanocrystallized Low-Carbon Steels During Gaseous Nitridation

An investigation on nitrogen uptake and microstructure of equimolar quaternary FeCoNiCr high entropy alloy after active-screen plasma nitriding

Mechanical Properties and Optimal Grain Size Distribution Profile of Gradient Grained Nickel

Nitriding Behavior of Nanocrystalline NdFe10.5VTi0.5 Compounds

Nurmerical simulation of nitrogen concentration profile in 42CrMo steel during plasma nitriding

Synergistic Effect of Nitrogen and Refractory Material on TiN Formation and Equiaxed Grain Structure of Ferritic Stainless Steel

Microstructure and Mechanical Properties of Cr Films with Different Orientations Before and after Plasma Nitriding

Homogenization of Nitrogen in Fe-3Si Alloy at High-Temperature Annealing Process

Surface nanocrystallization of pure iron achieved by anodization-reduction treatment and its effect on lower-temperature nitriding behaviors

A Novel Single-Step Surface-Treatment Process for Forming Cr-Nitride Coatings on Steels

Simulations of Nanocrystalline Iron Formation under High Shear Strain

Effect of recrystallization on diffusion in ultrafine grained Ni

Gradient Nanotwinned Structure and Its Formation Mechanism in Inconel 625 Alloy Produced by Surface Mechanical Grinding Treatment

Ultrafast atomic transport in recrystallizing ultrafine grained Ni

Stress Induced Anisotropic Diffusion During Plasma-Assisted Nitriding of A Ni-Based Alloy

From mechanical behavior and elastocaloric effect to microscopic mechanisms of gradient-structured NiTi alloy: A phase-field study