Abstract:As the power density of the power transmission device increases, heat exchangers are required to dissipate more heat and provide better flow resistance in the limited space of the vehicle. In this study, the synergy mechanism of the temperature field, pressure field, and velocity field in the serrated fin channel of the plate-fin heat exchanger (PFHX) was thoroughly analyzed under the guidance of the three-field synergy principle. This study also quantitatively revealed the distribution of the angle θ between the temperature gradient and velocity, and the angle α between the pressure gradient and velocity. For the regions in the channel where θ was too large (i.e., poor synergy between temperature and velocity fields) and α was too small (i.e., poor synergy between pressure and velocity fields), high-efficiency and low-resistance fin structures were proposed. The performance improvement of the new structures was quantified using the comprehensive heat transfer and flow resistance performance evaluation plot in the three-field synergy standard. The results indicate that the new structures improve the synergy of the three fields in the channel. When the air velocity is 15 m s −1 , the average synergy angle θ m between the temperature gradient and the velocity of the two structures, changing the inlet flow direction and the slotted fin, decreases from 83.4° to 80.3° and 82.8°, respectively. The outlet temperature increases by 2.3 and 1.6 K, respectively, compared to the basic structure, indicating enhanced the heat transfer of the PFHX. By changing the shape of the fin cross-section, the average synergy angle α m between the pressure gradient and the velocity increased from 143.6° to 150.8°, while θ m increased by only 0.6°. The pressure loss was reduced by 15.2% compared to the basic structure, resulting in a significant decrease in pressure drop while maintaining essentially the same heat transfer performance. Meanwhile, the optimized PFHX can increase the heat transfer rate by 0.2%–8% under identical pump power. This work provides guidance on selecting high-efficiency and low-resistance vehicle-mounted PFHXs.

Feasibility Study of the Ф5 Tube-and-fin Heat Exchanger in Automotive Heat Pump System

Study on heat transfer and friction characteristics in fin-tube heat exchangers used for electrical machines cooling

An Experimental Study on the Air Side Heat Transfer Performance of the Perforated Fin-Tube Heat Exchangers under the Frosting Conditions

Experimental investigation on frosting performance of a microchannel heat exchanger in heat pump system for electric vehicles

Optimization study of the circuitry for 5 mm small-diameter finned-tube heat exchanger in air-source heat pumps

Enhancing Plate-Fin Heat Exchanger Hydraulic Thermal Performance Through Air-Side Fin Optimization Based on Pseudo-3D Topology Optimization

Analyses of the thermal and hydraulic characteristics of a perpendicular-flow offset-strip-fin heat exchanger for electric vehicles

An experimental investigation on the frosting and defrosting process of an outdoor heat exchanger in an air conditioning heat pump system for electric vehicles

Performance Evaluation of a Vertical-Finned Microchannel and a Fin-Tube Heat Exchangers under Wet and Frosting Conditions

Configuration Design and Experimental Investigation of Fin Used in 5mm Fin-and-tube Heat Exchangers for Air Conditioner

Performance Improvement of Vapor Compression Heat Pump with Superhydrophobic Finned-Tube Evaporator

Superhydrophobic Microchannel Heat Exchanger for Electric Vehicle Heat Pump Performance Enhancement

Experimental Investigation of the Performance of Microchannel Heat Exchangers with a New Type of Fin under Wet and Frosting Conditions

Study on high-efficiency and ultra-thin heat exchanger

Numerical investigation on Enhancing Heating performance in Automotive Radiator

Exploration and numerical study of new structures for high-efficiency and low-resistance vehicle-mounted plate-fin heat exchanger based on the three-field synergy principle

Experimental and Theoretical Analysis for Heat Transfer and Flow Performance of Mini-channel Parallel Flow Heat Exchanger in Vehicle

Influence of Heat Exchanger Tube Layout on Performance of Heat Pump System for Electric Cars

Experimental Study on the Frosting and Heat Transfer Performance of Three Rows of Variable Pitch Finned Coils

Development and Performance Evaluation of CO2 Automotive Heat Pump System Applied to-20 ℃ Environment

Condensation heat transfer performance of R290 in a plate heat exchanger for electric vehicle heat pumps