Abstract:Recently, microchannel heat exchangers (MCHX) have been widely used in heat pump systems due to their high surface-to-volume ratio and high efficiency of heat transfer. However, when the MCHX operates in frosting conditions, its performance is adversely affected. To study the frost formation and distribution characteristics of MCHX, a comprehensive parametric study was performed for the MCHX with a larger fin pitch. The effects of fin geometries and environmental parameters on the frosting characteristics of MCHX were studied. Fin height ( F h ) can effectively inhibit frost formation, which is due to the increase of surface temperature with the increase of F h . When F h increased from 6.0 mm to 11.8 mm, the frost time increased by 30.5 %. However, the increase in F h also brings the penalty of reduced heat transfer rate. The effect of fin depth ( F d ) on frost formation performance is small because the frost is mainly deposited in the front part, resulting in the rear fin cannot work efficiently. Fin pitch ( F p ) is the most significant structural parameter affecting frosting performance. When F p increases from 1.6 mm to 4 mm, the frosting time increases by 4 times and frost mass increased by 2.2 times. This is because with the increase of F p , the frost blocking in the front part can be effectively delayed, and the distribution uniformity of the frost layer is improved. Lower surface temperature and higher humidity ratio significantly promote frost formation and reduce the uniformity of frost distribution. When the inlet temperature is reduced from -5 degrees C to -8 degrees C, the frosting time is shortened by 2.15 times, and the frost mass is reduced by 55.7 %. When the relative humidity increases from 76 % to 92 %, the frosting time is shortened by 2.15 times, and the frost mass is reduced by 42.5 %. The air velocity has a minor impact on the growth rate of frost in the front part. However, as the air velocity increases, the uniformity of frost distribution is significantly improved. When the air velocity increased from 1.1 m s - 1 to 2.2 m s - 1 , the mass of accumulated frost increased by 29.5 %. Furthermore, frost thickness and air-side heat transfer coefficient correlations were developed by testing 12 samples. The developed heat transfer coefficient correlation can accurately capture the changing trend of the j -factor. This study provides a fundamental understanding of the frosting characteristics of MCHX and can effectively guide the louvered fin optimization.

Experimental Investigation of the Performance of Microchannel Heat Exchangers with a New Type of Fin under Wet and Frosting Conditions

An Experimental Study on the Air Side Heat Transfer Performance of the Perforated Fin-Tube Heat Exchangers under the Frosting Conditions

Experimental investigation of frost and defrost performance of microchannel heat exchangers for heat pump systems

Performance Evaluation of a Vertical-Finned Microchannel and a Fin-Tube Heat Exchangers under Wet and Frosting Conditions

Performance Improvement of Microchannel Heat Exchangers with Modified Louver Fins under Frosting Conditions

Study on heat transfer and friction characteristics in fin-tube heat exchangers used for electrical machines cooling

Research Progress of Frost Formation on Microchannel Heat Exchangers

Experimental Study of Cyclic Frosting and Defrosting on Microchannel Heat Exchangers with Different Coatings

Experimental Study of Frost Formation on Cold Surfaces with Various Fin Layouts

Frosting Characteristics of Microchannel Heat Exchangers: Parametric Studies and Correlation Development

Numerical Prediction of Frosting Growth Characteristics of Microchannel Louvered Fin Heat Exchanger

An Experimental study of low-temperature finned-tube heat exchanger in frosting conditions

Experimental Research on Frost Performance of MicroChannel Heat Exchanger

Study on Performance of Forced Convection Finned-Tube Exchanger under Frosting Conditions

An Experimental Study on the Effects of Frosting Conditions on Frost Distribution and Growth on Finned Tube Heat Exchangers

A modeling study of spatial and temporal frost growth on the edge of windward fins for a tube-finned heat exchanger

Experimental investigation on frosting performance of a microchannel heat exchanger in heat pump system for electric vehicles

Performance of the frosting characteristics of fin-and-tube heat exchanger subject to superhydrophobic coating

Experimental Study on the Frosting and Heat Transfer Performance of Three Rows of Variable Pitch Finned Coils

Condensate drainage on slit or louvered fins in microchannel heat exchangers for anti-frosting

Experimental study on the frosting and heat transfer characteristics of cooling surfaces in confined parallel and counter flow channels