Abstract:Recently, microchannel heat exchangers (MCHX) have been widely used in heat pump systems due to their high surface-to-volume ratio and high efficiency of heat transfer. However, when the MCHX operates in frosting conditions, its performance is adversely affected. To study the frost formation and distribution characteristics of MCHX, a comprehensive parametric study was performed for the MCHX with a larger fin pitch. The effects of fin geometries and environmental parameters on the frosting characteristics of MCHX were studied. Fin height ( F h ) can effectively inhibit frost formation, which is due to the increase of surface temperature with the increase of F h . When F h increased from 6.0 mm to 11.8 mm, the frost time increased by 30.5 %. However, the increase in F h also brings the penalty of reduced heat transfer rate. The effect of fin depth ( F d ) on frost formation performance is small because the frost is mainly deposited in the front part, resulting in the rear fin cannot work efficiently. Fin pitch ( F p ) is the most significant structural parameter affecting frosting performance. When F p increases from 1.6 mm to 4 mm, the frosting time increases by 4 times and frost mass increased by 2.2 times. This is because with the increase of F p , the frost blocking in the front part can be effectively delayed, and the distribution uniformity of the frost layer is improved. Lower surface temperature and higher humidity ratio significantly promote frost formation and reduce the uniformity of frost distribution. When the inlet temperature is reduced from -5 degrees C to -8 degrees C, the frosting time is shortened by 2.15 times, and the frost mass is reduced by 55.7 %. When the relative humidity increases from 76 % to 92 %, the frosting time is shortened by 2.15 times, and the frost mass is reduced by 42.5 %. The air velocity has a minor impact on the growth rate of frost in the front part. However, as the air velocity increases, the uniformity of frost distribution is significantly improved. When the air velocity increased from 1.1 m s - 1 to 2.2 m s - 1 , the mass of accumulated frost increased by 29.5 %. Furthermore, frost thickness and air-side heat transfer coefficient correlations were developed by testing 12 samples. The developed heat transfer coefficient correlation can accurately capture the changing trend of the j -factor. This study provides a fundamental understanding of the frosting characteristics of MCHX and can effectively guide the louvered fin optimization.

Performance Improvement of Microchannel Heat Exchangers with Modified Louver Fins under Frosting Conditions

An Experimental Study on the Air Side Heat Transfer Performance of the Perforated Fin-Tube Heat Exchangers under the Frosting Conditions

Frosting Characteristics of Microchannel Heat Exchangers: Parametric Studies and Correlation Development

Experimental Investigation of the Performance of Microchannel Heat Exchangers with a New Type of Fin under Wet and Frosting Conditions

Temperature-gradient-enabled Prohibition of Condensation Frosting on Fin Surfaces

Numerical Prediction of Frosting Growth Characteristics of Microchannel Louvered Fin Heat Exchanger

Research Progress of Frost Formation on Microchannel Heat Exchangers

Performance Evaluation of a Vertical-Finned Microchannel and a Fin-Tube Heat Exchangers under Wet and Frosting Conditions

Thermal-hydraulic and Drainage Performance of Microchannel Heat Exchangers for Refrigeration and Heat Pump Systems under Frosting, Defrosting, and Wet Conditions: A Comprehensive Review

Experimental investigation of frost and defrost performance of microchannel heat exchangers for heat pump systems

A New Defrosting Model for Microchannel Heat Exchanger Heat Pump System Considering the Effects of Drainage and Water Retention

Experimental Research on Frost Performance of MicroChannel Heat Exchanger

A modeling study of spatial and temporal frost growth on the edge of windward fins for a tube-finned heat exchanger

Comparison of Energy Supplies and Consumptions in Heat Pump Systems Using Finned Tube and Microchannel Heat Exchangers During Defrosting

An Experimental Study on the Effects of Frosting Conditions on Frost Distribution and Growth on Finned Tube Heat Exchangers

Frosting Behavior of Louvered-Fin and Tube Heat Exchanger after Surface Treatment: Experimental Analysis

Enhancing heat-exchanger performance in frost conditions via superhydrophobic surface modification

Study on Performance of Forced Convection Finned-Tube Exchanger under Frosting Conditions

A Study on the Performance of the Airside Heat Exchanger under Frosting in an Air Source Heat Pump Water Heater/chiller Unit

Experimental investigation on frosting performance of a microchannel heat exchanger in heat pump system for electric vehicles

Experimental Study of Frost Formation on Cold Surfaces with Various Fin Layouts