Abstract:This article focuses on the problem of fluctuating cooling system flow caused by different working states such as acceleration and braking during the actual operation of electric vehicles, which prevents the system from effectively dissipating heat from the battery for a long time. In the past, liquid cooling heat dissipation schemes designed based on structural parameters often relied on the experience of CFD engineers. There is no in-depth study of the heat propagation characteristics. At present, research on the application of topology optimization method in cooling plate design mainly focuses on the relative positions of single inlet and outlet, objective functions, and constraint conditions. There are very few studies evaluating the adaptability of different cooling plate structures at different flow rates. In this perspective, this work proposes a two-dimensional topology optimization method for obtaining the cooling plates with different topological structures such as the series of cooling plate structures with dual entrances and exits. The method comprises of a comprehensive study on variations of the inlet flow rate under different average fluid volume fraction, outlet width, and temperature weight conditions. The results indicate that setting an excessive inlet flow rate can actually lead to an increase in the average temperature of the optimized cooling plate. Subsequently, the cooling plate structure obtained through topology optimization at inlet flow rates of 0.015 m/s, 0.02 m/s, and 0.025 m/s was selected, and a three-dimensional electrothermal fluid coupling model was established based on its two-dimensional channel structure. Its cooling performance, flow characteristics, and heat transfer characteristics were analyzed, and compared with two straight channel reference models. The results indicate that the optimized cooling plate structure under low flow conditions has better heat dissipation performance. At a flow rate of 0.56 × At 10 -6 m 3 /s, compared to traditional cooling plates(CASE D, CASE E), the highest temperature of the battery using topology optimized cooling plates (CASE A) decreased by 3.5 K and 1.79 K, respectively, and the standard deviation of temperature decreased by 48% and 14%, respectively. Under the same inlet flow velocity, the area of the fluid region increases with the increase of the mean fluid volume fraction, and the width of the flow channel increases gradually and the branches increase significantly, from the concentrated solid region to the dispersed isolated region. At a low flow rate, the normalized temperature of the cooling plate increases with the increase of the flow rate of the coolant inlet, and when the flow rate reaches a certain value, in order to reduce the power loss of the cooling plate, the flow path is gradually concentrated on both sides of the cooling plate. This leads to the decline of the normalized temperature of the cooling plate.

Enhancing Plate-Fin Heat Exchanger Hydraulic Thermal Performance Through Air-Side Fin Optimization Based on Pseudo-3D Topology Optimization

Non-linear mapping and multi-objective optimization of leading flow structure in plate-fin heat exchanger

Thermohydraulic Performance Optimization of Integrated Porous Pin Fins in Microchannel Heat Sink Using Shape Optimization Coupled with NSGA

An Experimental Study on the Offset-Strip Fin Geometry Optimization of a Plate-Fin Heat Exchanger Based on the Heat Current Model

Exploration and numerical study of new structures for high-efficiency and low-resistance vehicle-mounted plate-fin heat exchanger based on the three-field synergy principle

Design and experimental investigation of topology-optimized fin structures for enhanced heat transfer in latent heat thermal energy storage units

Design and Optimization of a Thermoelectric Generator with Dimple Fins to Achieve Higher Net Power

On the Heat Transfer Enhancement of Plate Fin Heat Exchanger

Comprehensive performance investigation and optimization of a plate fin heat exchanger with wavy fins

Simulation and Optimization Study on the Performance of Fin-and-Tube Heat Exchanger

Maximizing liquid-cooled heat sink efficiency with advanced topology-optimized fin designs

Taguchi optimization and thermoelectrical analysis of a pin fin annular thermoelectric generator for automotive waste heat recovery

Model-Based Performance Optimization of Thermal Management System of Proton Exchange Membrane Fuel Cell

A comprehensive numerical study based on topology optimization for cooling plates thermal design of battery packs

Topology optimization, additive manufacturing and thermohydraulic testing of heat sinks

Numerical Simulation and Experimental Verification on Thermal Performance of A Novel Fin-Plate Thermosyphon

Performance study on a printed circuit heat exchanger composed of novel airfoil fins for supercritical CO2 cycle cooling system

Heat transfer enhancement technology for fins in phase change energy storage

Optimization of Thermoelectric Performance of Offset-strip Fin Type Exhaust Heat Exchanger

Topology optimization and bionic analysis of heat sink fin configuration based on additive manufacturing technology

Genetic Algorithm Based Topology Optimization of Heat Exchanger Fins Used in Aerospace Applications