Abstract:With the increasing demand of the electricity, an efficiency improvement and thereby a reduced CO2 emission of the coal-fired plants are expected in order to reach the goal of the Kyoto protocol. In the medium term, increase of thermal efficiency of the steam cycle can be achieved by a rise of the process parameters. Currently, live steam pressures and temperatures up to 300 bar and 923 K are planned as a next step. This means an increase of 50-100 K in comparison to plants presently under operation. Such a large increase will only be possible, if all thermally high loaded components of the plant are made of new materials and/or new technologies for cooling and thermal insulation are applied.Closed circuit steam cooling of blades and vanes in modern steam turbines is a promising technology in order to establish elevated live steam temperatures in future steam turbine cycles. Due to the cooling of the components, materials can be used, which are common in todays application. In this paper, a steam-cooled test vane in a cascade with external hot steam flow is analysed numerically by applying a Conjugate Calculation Technique. The boundary conditions of the hot steam are derived from the planned inlet parameter of the HP steam turbine in a medium term and a long term in order to show the application potential of such a cooling technique. The supply steam parameters of the cooling are set equal to those of the outlet steam from the HP steam turbine.The results show that the steam cooling technique can reach necessary cooling effectiveness in the steam turbine by using only minor amounts of cooling steam. The internal pan of the vane is cooled homogeneously in both investigated cases. Basic features and phenomena of the steam cooling technique in steam turbines are discussed in the paper with respect to future application. It has been found that the trailing edge region of the steam-cooled vane is less critical with respect to high thermal load than in gas turbine application with the same configuration. At the leading edge of the vane, high thermal load can be detected because of the direct impingement of the hot steam. Improvement of the leading edge cooling is recommended by increasing cooling steam amount for the leading edge channel. Thus, a larger diameter of the channel can increase internal cooling efficiency for the leading edge. Due to the different heat transfer characteristics on the suction side and pressure side, the suction side shows also a higher temperature distribution in the investigated cases.

Application of Evaporative Cooling Technique to Large Turbo Generator

Experimental Research of Open Channel Evaporative Cooling of Turbo Generator's Rotor Windings

Water Cooling System Design and Thermal Analysis for Electrical Vehicle Driving Motors

Feasibility Analysis of the Application of Evaporative Condensers to Cooling System in Thermal Power Plant

Ventilation and Stator Temperature Field of Bulb Tubular Turbine Generator

Multi-objective Optimization of Transpiration Cooling for High Pressure Turbine Vane

Transpiration Cooling of High Pressure Turbine Vane with Optimized Porosity Distribution

Optimal Analysis on Temperature Field of Stator Ventilation System Based on Longitudinal Vortex Generator

Generation Mechanism of DC Flow in Double-Inlet Pulse Tube Coolers

Performance of air/spray cooling system for large-capacity and high-power-density motors

Simulation Study on Closed-circuit Ventilation System of Large Vertical Hydraulic Turbine Generator

Heat transfer coefficient distribution in inner surface of stator ventilation duct for large capacity air-cooled turbine generator

Numerical Calculation of Fluid Heat Transfer in Rotor of Large Air-cooled Generator Based on Global Ventilation Network Model

Stator Non-Uniform Radial Ventilation Design Methodology for a 15 MW Turbo-Synchronous Generator Based on Single Ventilation Duct Subsystem

Influence of Complex Fluid Flow on Temperature Distribution in the Rotor Region of Large Hydrogenerator Under the Rotor Rotation

Windings Indirect Liquid Cooling Method for a Compact Outer-Rotor PM Starter/Generator With Concentrated Windings

Coupled Aerothermodynamics Optimization for the Cooling System of a Turbine Vane

Application of Evaporative Cooling Technology in Transformer for Mine Tunnels

A Comparative Study on Coupled Fluid–Thermal Field of a Large Nuclear Turbine Generator with Radial and Composited Radial–Axial–Radial Ventilation Systems

Cooling Performance Of The Steam-Cooled Vane In A Steam Turbine Cascade

Theoretical analysis of a direct-coupled Stirling combined cooling and power system for heat recovery