Abstract:Nanofibers exist ubiquitously in natural extracellular matrix (ECM) of all kinds of human tissues forming hydrated interwoven network. Electrospinning nanotechnology has been proven to be a powerful technique to fabricate controllable nanofibers mimicking the natural ECM structures. Hyaluronic acid (HA), as a critical component of natural ECM, has been widely used in tissue engineering and regenerative medicine. In this study, pure HA nanofibers with average diameter of 33 +/- 5 nm, 59 +/- 12 nm, 79 +/- 12 nm and 113 +/- 19 nm were successfully prepared using different electrospinning parameters. The effect of the ambient relative humidity on HA electrospinnability was investigated for the first time in detail, which was proven to be one of the most important factors to control the morphology of HA nanofibers beside the solution properties. A critical value of humidity for a defined HA solution was observed, only below which HA nanofibers with similar diameters and morphologies could be successfully obtained. When the ambient relative humidity was higher than the critical value, the HA nanofibers started dissolving at the cross points and even fused together forming a spreading layer. Moreover, only a small amount of N, N-Dinnethylformamide (DMF) was found to be required to promote the electrospinnability of HA solution by mixing with water as solvents. With the increase in the DMF content, the surface tension of the solution decreased significantly, which was thought to be benefit for the stable Taylor cone and fluid jet formation in electrospinning. At the same time, it should be noted that the conductivity of the solution also decreased with the increase of DMF content in the solution, which was believed to be responsible for the increasing diameters of HA nanofibers corresponding to higher DMF content. Controllable HA nanofibers with diameter below 100 nm have great promising for developing novel nanobiomaterials applied in tissue engineering and regenerative medicine.

Control of the Porous Surface Morphology of Polyoxymethylene Electrospun Fibers

Experimental Investigation of the Effect of Processing Parameters on the Formation of Electrospun Polyethylene Oxide Nanofibers

Preparation and Structural Control of Polyethylene Hollow Fiber Membranes

Morphological Modulation of Electrospun PVDF/PVP Nanofibers

Controlling Pore Size and Wettability of A Unique Microheterogeneous Copolymer Film with Porous Structure

Experimental Investigation of the Governing Parameters in the Electrospinning of Polyethylene Oxide Solution

Phase Morphology and Mechanical Properties of the Electrospun Polyoxymethylene/polyurethane Blend Fiber Mats

Humidity-Controlled Preparation of Flexible Porous Carbon Fibers from Block Copolymers

Study on electrospinnability of PVP/PEO composite micro-nano fibers

The impact of relative humidity on electrospun polymer fibers: From structural changes to fiber morphology

The effects of electrospinning parameters on coaxial polyacrylonitrile/polyurethane nanofibers: Morphology and water vapour transmission rate

Advancing Nanofiber Research: Assessing Nonsolvent Contributions to Structure Using Coaxial Electrospinning

Preparation and Properties of Poly (vinyl Alcohol) Nanofibers by Electrospinning

Effects of Solvent on Structures and Properties of Electrospun Poly(ethylene Oxide) Nanofibers

PREPARATION OF POROUS POLYACRYLONITRILE ULTRATHIN FIBERS BY ELECTROSPINNING WITH NONSOLVENT INDUCED PHASE SEPARATION

The Influence of Sheath Solvent Compositions on the Diameters of Electrospun PCL/PTMC Nanofibers

A simple and effective approach to regulate and control pore structure of electrospun PTFE nanofiber membrane

Preparation of porous polyacrylonitrile fibers by electrospinning a ternary system of PAN/DMF/H2O

Effects of ambient relative humidity and solvent properties on the electrospinning of pure hyaluronic acid nanofibers.

Controlling the surface structure, mechanical properties, crystallinity, and piezoelectric properties of electrospun PVDF nanofibers by maneuvering molecular weight

Preparation of porous hollow polyacrylonitrile ultrafine fibers by coaxial electrospinning