Abstract:In this research, nonwoven nanofiber mats were prepared using the electrospinning method for the solution of polyurethane polymer dissolved in acetic acid. Effects of solution concentration, solution flow rate, as well as high voltage on the morphonology and wettability of the prepared nanofibers were studied. Nanofiber morphology was investigated through the analysis of scanning electron microscopy (SEM) micrographs using ImageJ software, while the wettability of the nanofiber mat surfaces was studied through the measurement of the contact angle. Results revealed that when the concentration of the solution was changed from 8wt% to 12wt%, the average nanofiber diameter showed a significant increase from 0.326 μm to 0.380 μm, while the contact angle increased from 39 degrees to 79 degrees. Results also showed that when the applied high voltage was changed from 10 KV to 25 KV, the average nanofiber diameter decreased and then increased within the range of 0.380 to 0.497 μm and that the contact angle was increased from 81 degrees to 108 degrees showing an obvious switching from hydrophilic towards hydrophobic surface. When the syringe pump flow rate was changed from 0.012 ml/min to 0.02 ml/min, morphology measurements showed that the average nanofiber diameter showed a significant increase from 0.351 μm to 0.456 μm, and the surface contact angle was also increased from 43 degrees to 98 degrees. Finally, the results of Fourier Transform Infrared Spectroscopy (FTIR) and X-ray diffraction analysis (XRD) tests showed that the electrospun polyurethane polymer material used in this work was not changed during the electrospinning process.

The effects of electrospinning parameters on coaxial polyacrylonitrile/polyurethane nanofibers: Morphology and water vapour transmission rate

Coaxial Electrospinning Of Polyurethane(Shell)/Nylon-6(Core) For Textile Applications

Composite Nanofibers for Textile Applications

Preparation and Characterization of Nylon-6/Poly(vinyl Alcohol) Ultrafine No-Woven Fabrics

Preparation and Characterization of Core—Shell Structured Nanofibers by Coaxial Electrospinning

Coaxial electrospun poly(methyl methacrylate)-polyacrylonitrile nanofibers: atomic force microscopy and compositional characterization.

INVESTIGATION OF THE IMPACT OF DIFFERENT PARAMETERS ON THE MORPHOLOGY OF ELECTROSPUN POLYURETHANE NANOFIBERS

Preparation of PVDF/PVP core–shell nanofibers mats via homogeneous electrospinning

Study on Morphology Features and Mechanical Properties of Nanofibers Films Prepared by Different Composite Electrospinning Methods

Preparation and Characterization of Pva/Pu Blend Nanofiber Mats by Dual-Jet Electrospinning

Effects of Electrospinning Technological Parameters on Diameter of Polyacrylonitrile Insulation Nano-fiber

Coaxial Electrospinning and Characterization of Core-Shell Structured Cellulose Nanocrystal Reinforced PMMA/PAN Composite Fibers

Fabrication of Core–shell Nanofibers by Single Capillary Electrospinning Combined with Vapor Induced Phase Separation

Morphology and Mechanical Properties of MWNTs/PU Compound Nanofibers

Adhesion and protective properties of electrospun PVA/ES composites obtained by using spiral disk spinnerets

Comparatively Thermal and Crystalline Study of Poly(Methyl-Methacrylate)/Polyacrylonitrile Hybrids: Core-Shell Hollow Fibers, Porous Fibers, and Thin Films

Advancing Nanofiber Research: Assessing Nonsolvent Contributions to Structure Using Coaxial Electrospinning

Preparation of PAN@PU coaxial electrostatic spun nanofibers for oil/water separation

Polyacrylonitrile and Carbon Nanofibers with Controllable Nanoporous Structures by Electrospinning

Enhancing mechanical strength of electrospun nanofibers by coaxial electrospinning and thermal treatment