Abstract:Digital light processing (DLP) is increasingly widely used to manufacture high-precision complex structural ceramic components quickly and efficiently. However, due to the high absorbance of silicon carbide (SiC) micron fine powder and the high refractive index difference between the powder and the photosensitive resin, it is extremely challenging to DLP print SiC with high precision complex structure. Here, the surface of SiC powder was coated with SiO 2 nano-layer of different thickness by controllable oxidation coating method, thus realizing the photocurable printing of SiC@SiO 2 green bodies with structural precision up to 80 μm. Through the two-step reaction method of carbothermal reduction combined with gas-phase siliconizing (GSI), not only the SiO 2 coated layer was effectively removed, but also the reaction-bonded silicon carbide (RB-SiC) ceramics with 80–300 μm periodic structure was successfully realized. Ultimately, the comprehensive performance of the RB-SiC samples is effectively improved by chemical vapor infiltration of silicon carbide (CVI-SiC). It is noteworthy that the maximum elastic modulus and hardness of the ultima SiC specimens (RB-SiC@CVI-SiC) are as high as 394.599 GPa and 50.241 GPa, respectively. Shockingly, the nanomechanical properties of postgenetic RB-SiC bound to initial α-SiC on the cross-section of ultima specimens were much higher than those of CVI-SiC on the surface. This study fills the gap that liquid-phase siliconizing (LSI) or pyrolysis process could not achieve high-performance SiC ceramics with micron-level periodic structure.

Fabrication of SiC Dense-Porous Laminates by Electrophoretic Deposition Process

Fabrication of Three-Dimensional Inter-Connective Porous Ceramics Via Ceramic Green Machining and Bonding

POLYMER-DERIVED SIC CERAMIC WITH TRIPLY PERIOD MINIMAL SURFACE STRUCTURE FABRICATION THROUGH DIGITAL LIGHT PROCESSING

Preparation of Complicated SiC Green Bodies via Aqueous Slip Casting

Electrophoretic Deposition of Pb(Zr,Ti)O3 Powders on Silicon Wafer and Sintering Densification Approach

Fabrication and Properties of SiC Porous Ceramics by Slip Casting Process

A Novel Method for the Preparation of Porous SiC

Preparation of a Dense/Porous BiLayered Ceramic by Applying an Electric Field During Freeze Casting

Fabrication of In-Ceram Dental Restoration by Aqueous Electrophoretic Deposition

Fabrication of Gradient Porous SiC Ceramics with Directional Pores Without Templates

Highly Porous LAS-SiC Ceramic with Near-Zero Thermal Expansion Prepared Via Aqueous Gel-Casting Combined with Adding Pore-Forming Agents

Microstructure and Properties of Porous Si3n4 Ceramics with A Dense Surface

Fabrication And Properties Of Porous Si3n4-Sio2 Ceramics With Dense Surface And Gradient Pore Distribution

Fabrication of continuously porous SiC–Si3N4 composite using SiC powder by extrusion process

Direct Coagulation Casting of Silicon Carbide Components

Controllable reduction of absorbance and two-step reaction for 3D-printed SiC ceramics with micron-level periodic structure

Microstructures, Mechanical Properties and Electromagnetic Wave Absorption Performance of Porous SiC Ceramics by Direct Foaming Combined with Direct-Ink-Writing-Based 3D Printing

Stereolithography-based additive manufacturing of lightweight and high-strength Cf/SiC ceramics

Preparation of HEMA gel-casted SiC ceramics combined with LPS sintering

Electrophoretic Deposition Forming of Sic-Tzp Composites in A Nonaqueous Sol Media

Fabrication, Structure and Properties of Porous SiC Ceramics with High Porosity and High Strength