Abstract:Journal of Fire Sciences, Ahead of Print. The fire growth rate of interior linings, furnishings, and construction materials is measured in full-scale fire tests such as the ASTM E84 Steiner Tunnel, the ISO 9705 room fire, and a passenger aircraft fuselage as the flame-spread rate, time-to-flashover, or time to incapacitation, respectively. The results are used to indicate the level of passive fire protection afforded by the combustible material or product in the test without providing any insight into the burning process. These large-scale tests require many square meters of product, are very expensive to conduct, and can exhibit poor repeatability–making them unsuitable for product development, quality control, product surveillance, or regulatory compliance. For this reason, smaller (0.01 m2) samples are tested in bench-scale fire calorimeters under controlled conditions, and these one-dimensional burning histories are correlated with the results of the two- and three-dimensional burning histories in full-scale fire tests by a variety of empirical and semi-empirical fire propagation indices, as well as analytic and computer models specific to the full-scale fire test. The approach described here defines the potential of a material to grow a fire in terms of cone calorimeter data obtained under standard conditions. The fire growth potential, λ (m2/J), is the coupled process of surface flame spread and in-depth burning that is defined as the product of ignitability (1/Eign) and combustibility (ΔQ/ΔE) obtained from a combustion energy diagram measured in a cone calorimeter at an external radiant energy flux [math] (W/m2) above the critical flux for burning, [math]. However, the potential for fire growth, λ≡ (1/Eign)(ΔQ/ΔE) is only realized as a hazard when the heat of combustion of the product per unit surface area, Hc (J/m2), is sufficient to grow the fire. The dimensionless fire hazard of a combustible product of thickness b is therefore, Π = λHc, while the fire hazard of the component materials is an average over the product thickness, π = Π/b. The measurement of λ, Π, and π from combustion energy diagrams of heat release Q (J/m2) versus incident energy E (J/m2) is described, as well as a physical basis for a fire growth potential that provides simple analytic forms for λ in terms of the parameters reported in cone calorimeter tests. Experimental data from the literature show that rapid fire growth in full-scale fire tests of combustible materials occurs above a value of Π determined by the severity of the fire test.

A Scientific Analysis of Stored Plastic Fire Tests

Fire parameters of recycled plastic pellets

Fire Experimental Study of Upright ESFR Sprinkler for Protection of High-rack Storage

A Review of Combustion and Flame Spread over Thermoplastic Materials: Research Advances and Prospects

Measuring the fire growth potential of combustible solids using a cone calorimeter

Materials identification in comparison of results among fire scaling and flammability studies

Experimental Investigation of Water-Based Fire Suppression Systems on External Façade Fires

Cross-Contamination of Ignitable Liquid Residues on Wildfire Debris—Effects of Packaging and Storage on Detection and Characterization

Fire Risk Rating Assessment for Wood Specimens Coated with Flame Retardant

Experimental Study of Single-pane Fire-resistant Glass Performance with Sprinkler Protection

Fire Resistance Evaluation of New Wooden Composites Containing Waste Rubber from Automobiles

Fire Tests with Automatic Sprinklers in an Intermediate Scale Tunnel

Analysis and Modeling of Ignitability of Polymers in the UL-94 Vertical Burning Test Condition

Designing fire safe interiors

Fire Test of Metal Sandwich Plates During a Window Spill Fire

Experimental Study On Car Fire In Garage Under Sprinkler Protection

Fire Safety Assessment of Halogen-Free Flame Retardant Polypropylene Based on Cone Calorimeter

3-D potential fire hazard assessment of the high impact polystyrene burst-resistant composites

The effects of various flame retardants on the combustion of polypropylene: Combining optical diagnostics and pyrolysis fragment analysis

Fire resistance of 3D printed concrete composite wall panels exposed to various fire scenarios

Fire safety evaluation of expanded polystyrene foam by multi-scale methods