Abstract:Powder metallurgy is an effective method to produce Cu-Al-based alloys for automotive and aerospace engineering components. The finer grain size, low cost, and low-temperature synthesis make this process more suitable than the other conventional production method such as melting and casting. The addition of Ni (austenite stabilizer) into the Cu increases the stability of Cu and refines the grain size. Again, the addition of Ni into the Cu-Al alloy increases the strength and hardness. In the present work, Cu-12Al alloys are developed by varying the wt.% of Ni content from 0 to 8 using powder metallurgy process through mechanical alloying method. Mechanical alloyed powder mixture is compacted by applying a load of 5 tons and sintered at 850 °C for 1 h under nitrogen atmosphere. It is found that α-Cu, γ2-Cu9Al4, and NiAl phases are presented in the Cu-12Al-Ni alloy which influences the properties of the alloy. The theoretical, sintered, and relative density values are decreased with increasing the wt.% of Ni content. However, the Vickers hardness of the alloy is improved by increasing the wt.% of Ni content up to 4 wt.% and then reduced for 8 wt.% of Ni content due to the coarsening and network-type structure of the NiAl phase. A higher amount of wear loss or wear rate is observed for the Cu-12Al and Cu-12Al-2Ni alloy than the Cu-12Al-4Ni and Cu-12Al-8Ni alloy. The presence of oxygen peaks in the EDS analysis revealed that an oxidative type of wear is occurred for the Cu-12Al alloy samples with varying the wt.% of Ni content. The electrochemical corrosion analysis revealed that the rate of corrosion is higher for Cu-12Al alloy without Ni. However, the rate of corrosion is reduced by increasing the wt.% of Ni content from 2 to 8.

Microstructure and Arc Erosion Characteristics of Ag/Ni Contacts by Mechanical Alloying

Reforming Nanostructured CuAg Alloy to Improve Ductility and Electrical Conductivity

Preparation of silver-nickel contact materials by mechanical alloying

Influence of Ni content on arc erosion behavior of Ag/Ni electrical contact materials

Comparative study of the microstructure and arc erosion resistance of Ag/Ti 2 AlX (X=C, N) electrical contact materials

Preparation and Arc Erosion Mechanism of Ni Skeleton Reinforced Ag-Based Contact Materials with CuO-Coated SnO2

Microstructure Analysis And The Effect Of Cr Additive On Electrical Performance Of (C-P-Nb)/Cu-Cd Electrical Contact Materials

The Beauty and the Deed of Silver During Arc Erosion of Ag/Ti3AlC2 Contacts

Microstructure transformation and mechanical behavior in NiTi alloys fabricated by dissimilar double wires arc additive manufacturing

Microstructure and Mechanical Properties of Twin-Wire Arc Sprayed Ni-Al Composite Coatings on 6061-T6 Aluminum Alloy Sheet

The Effect of Mechanical Alloying Technology on Microstrcture of Fe-Ni Alloy

Investigation of the Microstructure and Electrical Performance of Ag/SnO 2 In 2 O 3 Contacts with Nickel Addition Fabricated by Internal Oxidation

Microstructure, Mechanical, and Tribological Relationship in Cu-12Al-Ni Alloy with Respect to the Variation of Ni Content

Micro-alloying effects of Ni on the microstructure and mechanical properties of an Al-Zn-Mg-Cu-Sc-Zr alloy

Anisotropic Arc Erosion Resistance of Ag/Ti3AlC2 Composites Induced by the Alignment of Ti3AlC2

A Study about Fe-Ni Mechanical Alloying Process by Dry and Wet Method

RESEARCH ON THE DEVELOPMENT OF A NEW AgNi-BASED CONTACT MATERIAL FOR CONTROL APPARATUS WITH SMALL CAPACITY

Microstructure and Tribological Properties of Nicraly-Mo-Ag Composite by Vacuum Hot-Press Sintering

Microstructures and Mechanical Behaviors of NiAlFe Intermetallic Compounds

Enhanced mechanical and electrical performance of Ag-4wt%ZrB 2 contact materials prepared with different-sized Ag powder

Microstructural Analysis, Tribological, and Corrosion Behavior of Nix-Tiy Alloys Deposited Using μ-Plasma Additive Manufacturing Process