Abstract:Three kinds of α -triethylsiloxyl- ω -trimethoxysilyethyl-terminated oligomers (TES-PDMS-TMOS, TES-PTFPMS-TMOS, and TES-PDES-TMOS) were synthesized through an anion catalyzed non-equilibrium ring-opening polymerization reaction of cyclotrisiloxanes and subsequent hydrosilylation reaction with vinyltrimethoxysilane. As the in situ surface modification agent for mixed-size AlN inorganic fillers (1, 20 and 50 μm blended in a mass ratio of 3:5:9), these oligomers have been mixed with Vi-PDMS in a mass ratio of 1:2. Relative to that of silicone pastes using Vi-PDMS as the polymer matrix, the thermal conductivity of silicone pastes made from AlN particles treated with these oligomers is enhanced, while their thermal resistances decreased. With the change of the repeating unit structure in the oligomers, the silicone pastes prepared from these oligomer-treated AlN fillers differ significantly in filler content, thermal conductivity, and thermal resistance. When TES-PTFPMS-TMOS is used and filled with 800 parts (70.3 vol%) of hybrid AlN powders, a silicone paste with a thermal conductivity of 4.56 W/(m. K) could be achieved, which was 37.8% higher than that silicone paste using pure Vi-PDMS as the matrix. When TES-PDES-TMOS is used and filled with 900 parts (72.7 vol%) of hybrid AlN powders, the thermal conductivity of the silicone paste reaches 4.13 W/(m. K). Despite its thermal conductivity being only 3.5% higher relative to the silicone paste using only Vi-PDMS as the polymer matrix, its thermal resistance decreased by 20.3%. When TES-PDMS-TMOS is used and filled with 1200 parts (78.0 vol%) of hybrid AlN powders, the thermal conductivity of the silicone paste could reach up to 4.59 W/(m. K), together with a thermal resistance 29.6% lower than that of silicone paste where 1000 parts (74.7 vol%) of hybrid AlN particles filled in the Vi-PDMS. The heat dissipation of the 30 W high-brightness LED chip also illustrated the excellent thermal conductivities of these silicone pastes. The effect of another terminal group on the monotrimethoxysilylethyl-terminated asymmetric polysiloxanes on the thermal resistance of thermal interface materials was also discussed in detail.

Preparation and Characterization of Silicone Grease with High Thermal Conductivity and High Electrical Insulation

Study on Alumina/Carbon Material Thermal Grease

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Enhancement of thermal conductivity and insulation of silicone thermal interface material through surface modification and synergistic effects of nanofillers for thermal management of electronic devices

Comprehensive excellent performance for silicone-based thermal interface materials through the synergistic effect between graphene and spherical alumina

Enhancing the Effectiveness of Silicone Thermal Grease by the Addition of Functionalized Carbon Nanotubes

Free Arc Disperses-Sprays Carbon Nanotubes and Silicon Carbide, Preparing Thermal Silicone Grease

Thermal conductivity enhancement in thermal grease containing different CuO structures

Thermally conductive and highly electrically resistive grease through homogeneously dispersing liquid metal droplets inside methyl silicone oil

Three-Dimensional Heterostructured Reduced Graphene Oxide-Hexagonal Boron Nitride-Stacking Material for Silicone Thermal Grease with Enhanced Thermally Conductive Properties

Performance Probe and Selection of Heat Conductive Silicone Grease of the Heat Pump Water Heater

Performance of High-Speed Grease Lubricated Hybrid Ceramic Ball Bearing

Exploring Graphite-Based Thermal Greases For Optimal Microelectronic Device Cooling

Novel Heat‐conductive Composite Silicone Rubber

Effect of the grease thickener on tribological properties of Si3N4/GCr15 contact interface and the performance in hybrid ceramic ball bearing

Thermally Conductive Silicone Rubber Reinforced with Boron Nitride Particle

A high-performance thermally conductive and electrically insulating silver@siloxane/graphene/epoxy composites at low filler content: Fabrication, mechanism study of insulation and thermal conductivity enhancement

Liquid cooling system for battery modules with boron nitride based thermal conductivity silicone grease

Effect of segment structure of monotrimethoxysilylethyl-terminated asymmetric Polysiloxanes on the thermal management performance of AlN-filled silicone pastes

Theoretical analysis on thermal grease dry-out degradation in space environment

Coating dense Silicon Carbide layer on artificial graphites to achieve synergistically enhanced thermal conductivity and electronic insulation of polymer composites