Abstract:Effective thermal conduction between solid interfaces has emerged as a major bottleneck in heat dissipating heat from new-generation high-performance electronics. Gallium-based liquid metals (LMs), known for their high thermal conductivity, are gaining significant traction as thermal interface materials (TIMs) for enhanced thermal management. In this work, to address the key issues facing the application of gallium-based LMs as TIMs, including the lack of composition ratio data, poor coating performance and the need for improved thermal conductivity, two types of gallium-based LM-TIMs (Ga-In binary LM-TIMs and Ga-In-Sn ternary LM-TIMs) with different composition ratios were experimentally prepared, investigated and optimized. The thermal conductivities of the LM-TIMs at different temperatures (80 - 120 ℃) were tested, and the application reliability of the LM-TIMs was optimized by continuously destructing the oxide layer and filling micro copper particles. The influence of optimization parameters such as the duration of the destruction of oxide layer, the filling ratios of the particles and the particle size on the operation performance of the LM-TIMs was studied and analyzed. The results showed that the LM-TIMs exhibited excellent thermal conductivities of 29.6 - 38.5 W/(m·K), and the thermal conductivity increased with indium mass fraction and decreased with tin mass fraction. Significant improvements in coating performance were observed with the increase of the duration of destructing oxide layer, but it led to a reduction in thermal conductivity. Balancing coating performance and thermal conductivity, it was found that 30 min was the ideal duration. The filling of micro particles made up for the reduced thermal conductivity, and higher filling ratios and smaller particle sizes achieved better enhancement. In the experiment, a filling ratio of 5 % was appropriate because solidification occurred in LM-TIMs at higher filling ratios which weakened the thermal conductivity. This work provided valuable reference for the application and optimization of high thermal conductive gallium-based LM-TIMs.

Highly conductive thermal interface materials with vertically aligned graphite-nanoplatelet filler towards: High power density electronic device cooling

Experimental Investigation on Optimization of the Performance of Gallium-Based Liquid Metal with High Thermal Conductivity As Thermal Interface Material for Efficient Electronic Cooling

Soft and Self‐Adhesive Thermal Interface Materials Based on Vertically Aligned, Covalently Bonded Graphene Nanowalls for Efficient Microelectronic Cooling

Compliance-tunable thermal interface materials based on vertically oriented carbon fiber arrays for high-performance thermal management

Enhancement of thermal conductivity and insulation of silicone thermal interface material through surface modification and synergistic effects of nanofillers for thermal management of electronic devices

A Novel Thermal Interface Material Composed of Vertically Aligned Boron Nitride and Graphite Films for Ultrahigh Through-Plane Thermal Conductivity

Graphene/Polyolefin Elastomer Films as Thermal Interface Materials with High Thermal Conductivity, Flexibility, and Good Adhesion

Rational design of high-performance thermal interface materials based on gold-nanocap-modified vertically aligned graphene architecture

Metal-Level Thermally Conductive yet Soft Graphene Thermal Interface Materials

Thermal interface material with graphene enhanced sintered copper for high temperature power electronics

Enhanced thermal conductivity and lower density composites with brick-wall microstructure based on highly oriented graphite nanoplatelet: towards manufacturable cooling substrates for high power density electronic devices

Alveoli‐Mimetic Synergistic Liquid and Solid Thermal Conductive Interface as a Novel Strategy for Designing High‐Performance Thermal Interface Materials

High-performance non-silicone thermal interface materials based on tunable size and polymorphic liquid metal inclusions

Vertically Aligned Boron Nitride Nanosheets Films for Superior Electronic Cooling

Scalable Compliant Graphene Fiber-Based Thermal Interface Material with Metal-Level Thermal Conductivity via Dual-Field Synergistic Alignment Engineering

Environment-adaptive, anti-fatigue thermal interface graphene foam

Recent Advances in Thermal Interface Materials for Thermal Management of High-Power Electronics

A Novel Phase Change Composite with Ultrahigh Through-Plane Thermal Conductivity and Adjustable Flexibility

Millefeuille-Inspired Thermal Interface Materials based on Double Self-Assembly Technique for Efficient Microelectronic Cooling and Electromagnetic Interference Shielding

Improving through-plane thermal conductivity of PDMS-based composites using highly oriented carbon fibers bridged by Al2O3 particles

Aligning graphene nanoplates coplanar in polyvinyl alcohol by using a rotating magnetic field to fabricate thermal interface materials with high through-plane thermal conductivity