Abstract:Wear performance and mechanisms of PCBN tools with different CBN content (80% vol. and 95% vol.) and cutting edge geometry (honed edge radius, 0.05 mm chamfered edge width, and 0.10 mm chamfered edge width) in boring powder metallurgy (PM) steels had been evaluated. Post-cutting examination of the worn cutting inserts was performed using focus variation microscopy (FVM), scanning electron microscopy (SEM), and energy dispersive spectrometer (EDS). The advanced three-dimensional wear characterization parameters WRM, WMD, WAM, WMH, and WAA are used to measure the wear of PCBN tools. A novel characterization method of removed material (η1 = WMD/WRM) and adhered material (η2 = WMH/WAM) was used to measure the trend of tool wear in this paper. With the increasing of CBN content, the PCBN tool wear parameters WRM, WMD, and WAA were decreased; adhesion was increased by WAM and WMH parameter characterization. For the variation of cutting edge geometry, chamfered edge showed a higher tool life and better wear performance than honed edge radius. With the increasing of chamfered edge width from 0.05 to 0.10 mm, the three-dimensional wear WRM, WMD, WAM, and WMH were increased. WAA showed an opposite trend and parameters η1 and η2 showed a not convergence trend. Besides typical wear mechanisms such as diffusion, adhesion, abrasive, microchipping was observed on PCBN tool; the tool protection layer (TPL) formation and peeling and impact load could be the reasons to explain the microchipping that occurred on cutting edge. Tool life is measured by surface roughness and calculated according to the number of workpieces processed. The results showed that PCBN tool with 95% vol. CBN content and 0.10 mm chamfered edge width achieves higher tool life.

Study on wear mechanisms and grain effects of PCD tool in machining laminated flooring

Wear Behaviors of Pcd Tools in Turning Granite

Analysis on Mechanics Property of PCD Tool While Machining Ceramics Overlay of HPL Flooring

Research on Cutting Parameters of PCD Tool when Machining Wear Resistant Layer of High Pressure Laminated Flooring

Effect of diamond grain size on mechanical properties and cutting performance of PCD tool in milling of C f /SiC composites

Study on PCD Tool Wear in Hard Milling of Fully-Sintered 3Y-TZP Ceramics

Research and development of polycrystalline diamond woodworking tools

Study on Tool Wear of High Volume Fraction SiCp/Al Composites with Ultrasonic Vibration High Speed Milling

Influence of cutting parameters on PCD tool wear during milling tungsten carbide

Evaluation of Polycrystalline Diamond Tools in Milling of Pre-Sintered and Fully-Sintered Zirconia Ceramics

A novel hybrid micro-texture for improving the wear resistance of PCD tools on cutting SiCp/Al composites

Study on Fabrication and Cutting Performance of High Quality Diamond Coated PCB Milling Tools with Complicated Geometries

Experimental and Multiscale Numerical Investigation of Wear Mechanism and Cutting Performance of Polycrystalline Diamond Tools in Micro-End Milling of Titanium Alloy Ti-6Al-4V

Wear Characteristics of Polycrystalline Diamond Tools in Orthogonal Cutting of Cfrp/Ti Stacks

Cutting performance and wear behavior of diamond, coated cemented carbide and PCBN tools during milling of C f /SiC composites

Analysis and design of PCD milling tool for machining copper alloy materials

Finite Element Analysis on Stress Distribution of PCD Tool while Machining Al2O3 Ceramics Overlay

Edge fabrication and process optimization of precision woodworking PCD millers with disk electrical discharge machining

Cutting performance and tool wear mechanism of corrugated helical PCD tool in milling Cf/SiC composites

Study on Fabrication and Their Cutting Performance of High-quality Diamond-coated Tools with Complicated Shape

Wear performance and mechanisms of PCBN tools in boring of powder metallurgy steels