Analysis and Improvement of Single Phase Power Factor Corrector Circuit

DING Jiu-liang,SHI Guo-yong,CAO Xiao-hong

2007-01-01

Abstract:The principle of critical conduction mode power factor corrector circuit based on ST L6561 is introduced, the disadvantage of its high mains voltage oscillation is analysed and then a protective circuit is proposed

What problem does this paper attempt to address?

Study of a Single-stage Three-phase PFC DC/DC Converter With Series-parallel Connected Transforms

Teng-fei WANG,Kai-qi DAI,Zheng-shi WANG

2018-01-01

Abstract:A single-stage three-phase power factor correction (PFC) and transformer series-parallel DC/DC converter is designed to meet the demand of high power output of electric vehicle charger. The converter combines three-phase PFC topology with phase shifted full bridge topology, using variable frequency control, to achieve the input PFC, bridge switches zero voltage switching turning on (ZVS) and output voltage adjustable. The primary windings are connected in series, the secondary windings are followed by the full bridge rectifier and the indutor before connected to achieve power expansion and power automatic balance. The working principle of the converter is analyzed, the parameter design and the device selection are designed,and the principle of automatic power equalization of the transformer is analyzed. Finally, a prototype is designed to verify the effectiveness of the converter.
Design and Analysis of Single-Stage Power Factor Correction Converter with a Feedback Winding

Hao Ma,Yue Ji,Ye Xu

DOI: https://doi.org/10.1109/tpel.2009.2037739

IF: 5.967

2010-01-01

IEEE Transactions on Power Electronics

Abstract:A new single-stage power factor correction (SSPFC) converter is proposed for the adapter application, which is composed of a flyback converter, a feedback winding and a front-end input current shaper. Through the feedback winding, a direct energy transfer path is configured to improve the conversion efficiency and alleviate the voltage stress across the bulk capacitor. Moreover, the feedback winding is connected to the input through only two diodes, which results in low conduction losses. Equations and configurations are given to design the input current-shaping inductor and the magnetizing inductor of the transformer, which are operated in the discontinuous conduction mode (DCM) and the DCM/ continuous conduction mode boundary mode respectively for well-shaped current waveform and reduced bulk capacitor voltage. The theoretical analysis of the converter is verified by two SSPFC prototype circuits with 19 V/90 W output. One prototype achieves a high efficiency of 90.3%, while complying with IEC 61000-3-2 Class D standard. With a different turns ratio design, the power factor can be further improved to 0.97 in another prototype.
Modeling and Controller Design of Active Power Factor Correction Based on L6562A

CHEN Qian,WANG Zheng-shi,CHEN Hui-ming,LIU Guo-qiang

DOI: https://doi.org/10.3969/j.issn.1000-100x.2012.03.021

IF: 5.967

2012-01-01

IEEE Transactions on Power Electronics

Abstract:An introduction is made to describe the operation principle of APFC which is based on L6562A under TCM mode.Design process of the main parameters of APFC circuit and the feedback compensation loop are presented. The control transfer function and frequency characteristics,phase frequency characteristics are derived through small-signal model of APFC.In order to make the system stable,a good compensation network can be set up with MATH-CAD by using the Bode plots.According to the parameters obtained from theoretical analysis,the SABER simulation results show the consistent with the theoretical calculations.On this basis,an APFC prototype was designed with 60 W output power.Simulation and experimental results show that the closed-loop system can improve the accuracy and dynamic of the output voltage or current,so that the converter has good stability,high power factor and low THD.
An Analysis of Power Factor Corrector Chip UC3854

詹桦,韩雁

DOI: https://doi.org/10.3969/j.issn.1004-3365.2002.02.014

2002-01-01

Abstract:UC3854 is a power factor corrector circuit with good performance Using the average current model,UC3854 controls the state of the switching transistor in the circuit by outputting a series of PWM (Pulse Width Modulation) signals By this mean,it readjusts input current and output voltage to synchronization, thus fulfilling power factor correction
Study on Comparison of Two Methods of Passive Three-phase Power Factor Correction

SHI Jian-jiang,ZHANG Jian-guo

DOI: https://doi.org/10.3969/j.issn.1000-100x.2005.02.016

IF: 5.967

2005-01-01

IEEE Transactions on Power Electronics

Abstract:Aiming at the actuality that the extensive application of power electronics results in serious harmonic pollution and aeronautical power supplies demand on high reliability,the passive three-phase power factor correction have been applied in the aeronautical power supplies.There are two methods of the passive three-phase power factor correction:the first one is that the filter capacitors and inductors are applied in the input-end of alternating current,and the second one is that the filter capacitors and inductors are applied in the output-end of three-phase rectifier.The advantages and drawbacks of the two methods of the passive three-phase power factor correction aer concluded in this paper through simulation and analysis and verified by experiment.To reduce the voltage stress of power switching transistors,the second method of power factor correction was applied in aeronautical power supply.
Improvement of self-oscillation circuit by single-tube induction heating

Shangyang Chi,Yuling Li,Yingying Yao,Shiyao Zhang

DOI: https://doi.org/10.16791/j.cnki.sjg.2017.05.015

2017-01-01

Abstract:In view of the defects such as IGBT non zero voltage switch (ZVS), the large increase of the pulse rate, the increase of IGBT loss, etc., in the commonly-used low cost single-tube induction heating power, the operational mechanism of the power supply is analyzed in detail, and the essential reason that the circuit can't realize the ZVS is found.The method to realize the ZVS of the power supply by increasing the fixed delay is proposed, and the delay time range of the circuit is theoretically analyzed and deduced.Finally, a proper scheme to realize the fixed time delay is presented by increasing the number of comparators.An experimental platform for the 1 kW single-tube induction heating is established.The experimental results prove the correctness of the theoretical analysis and the effectiveness of the method.The theory and experimental platform can be used for a comprehensive experiment for the basic course of power electronic technology.
Steady-State and Dynamic Study of One-Cycle-controlled Three-Phase Power-Factor Correction

GZ Chen,KM Smedley

DOI: https://doi.org/10.1109/tie.2005.843920

IF: 7.7

2005-01-01

IEEE Transactions on Industrial Electronics

Abstract:One-cycle control power-factor correction (OCC-PFC) with vector operation is a promising rectification method that eliminates harmonics and improves the power factor. It features great simplicity, high performance, and excellent stability. This paper performs analysis and design of OCC-PFC in both the steady-state and dynamic transients. The sufficient stability condition for three-phase OCC-PFC is derived. Some typical large-signal perturbations in practice are then used to verify the theoretical predictions. The paper also provides some guidelines for the selection of the circuit parameters in practical application. All analysis results were verified by simulation or experiments based on a three-phase 1-kW pre-industrial OCC-PFC prototype.
Analysis and Design Considerations of Improving Power Factor at Light-Load in a CHB Rectifier with Common-Duty Control

Wending Zhao,Yu Qi,Congrang Jiang,Xinke Wu

DOI: https://doi.org/10.1109/iciea51954.2021.9516330

2021-01-01

Abstract:Multi-level CHB rectifier with common-duty-ratio control suffers from low power factor in light-load condition, which related to small boost inductance and insufficient gain of current compensator at line-frequency. In order to solve this problem, a practical design method based on proportional resonant compensator is proposed, which can realize the optimization of power factor under light load. Finally, the effectiveness of the design method is verified by experiments, and the light-load power factor of CHB rectifier is increased to 0.95.
Single Stage PFC Circuit with Full Bridge Structure

贲洪奇,冯驳,吴新科

DOI: https://doi.org/10.3321/j.issn:0367-6234.2003.04.010

2003-01-01

Abstract:A novel single stage power factor correction circuit with full bridge structure is proposed for application in middle or high power condition to perform power factor correction and AC/AC power conversion at the same time.Such problelms with a dual stages PFC circuit as complex circuit structure,too many components,low efficiency and high cost are solved. How to choose switch and its driving is discussed. The advantages of proposed circuit were verified by theoretical analysis and experiments.
Analysis and simulation study on single-phase H-bridge rectifier/inverter

CHEN Xian-ming,LV Hong-shui,LIU Guo-hua

DOI: https://doi.org/10.3969/j.issn.1005-7277.2012.05.001

2012-01-01

Abstract:The detailed study has been paid for PWM control of single-phase H-bridge rectifier/inverter,which is able to implement double-direction energy flow.It also compares advantages and disadvantages between singlepole and double-pole PWM inverter.When H-bridge operates as a rectifier,power factor correction(PFC) function must be implemented.Namely,input sinusoidal current and power factor 1 in AC side of the rectifier is satisfied.Also when H-bridge operates as an inverter,output sinusoidal current and power factor 1(when connects to electric grid) is ensured.At last,the simulation of H-bridge operation under one cycle control(OCC) is completed with Matlab/Simulink software.It verifies the validity of H-bridge analysis and control with single-pole PWM better than that of double-pole PWM.
High efficiency power factor correction power supply based on SiC device

Peng-fei FAN,Long XIAO,Jin-xiang ZHAN,Hao CHEN,Guo-zhu CHEN

DOI: https://doi.org/10.3969/j.issn.1001-4551.2017.04.015

2017-01-01

Abstract:Aiming at the problem that the bridge Boost power factor correction circuit was not efficient.The basic structure and control method of Boost power factor correction circuit,the characteristics and development process of SiC device were analyzed,and the scheme of using SiC device to enhance its power density was proposed.The design of important parameters in power factor correction circuit was introduced.A design method for PFC power inductor was introduced.The design steps were analyzed and the loss distribution of traditional bridge power factor correction circuit was analyzed.Several MOSFETs with different materials were selected and the corresponding 1.2 kW prototype was set up,and the efficiency of each prototype was measured.The results indicate that compares with infineon's latest super-junction structure with CoolMOS,ROHM's high current Si MOSFET,the use of SiC MOSFET can improve the efficiency of the bridge power factor circuit.
A ZCS AC/DC CONVERTER WITH HIGH POWER FACTOR BASED ON PWM CONTROL STRATEGY

贲洪奇,吴新科,刘昭和

DOI: https://doi.org/10.3321/j.issn:0258-8013.2003.09.010

2003-01-01

Abstract:At present, the research of the single-stage power factor correction (PFC) circuits is mostly concentrated on the application of low powers. A zero-current-switching (ZCS) single-stage AC/DC converter with high power factor is proposed to use in medium and high power conditions. The PWM control is achieved by adding two auxiliary switches to the full bridge converter. The proposed converter can achieve zero-current switching and PFC in a very wide load range. It doesn't have the problem that the pulse frequency modulation (PFM) must be adopted in the full bridge resonant circuits if phase-shifted control is not used. The dynamic response of the proposed converter is faster, the cost is lower and the voltage stress of the switches is also lower as compared with the two-stage PEC converter's characteristics. The advantages are verified by the results of the simulation and experiments.
Development of Single-phase Power Factor Corrector Based on Si8250 Digital Controller

CHEN Shu-mei,ZHANG Dong-lai,CAI Zhi-kai

DOI: https://doi.org/10.3969/j.issn.1000-100x.2007.05.034

IF: 5.967

2007-01-01

IEEE Transactions on Power Electronics

Abstract:This paper proposes a 2660W Boost Power Factor Corrector(PFC) based on si8250 digital controller of the Silicon Labs company.This PFC was realized by employing sliding-mode variable-structure inner current loop control and outer voltage loop PI control with digital low-pass filter to achieve high performance.The experimental results proved that this PFC can get steady 420V output voltage when input voltage range from 90V to 264V.It also has good dynamic charac-teristics and strong robustness.
A Single-stage Power Factor Correction Converter with Constant Power Control

Zhaoming Qian

2004-01-01

Abstract:A novel single stage power factor correction converter with constant power control is presented. The PFC stage operates in discontinuous current mode (DCM) to achieve low THD and high PF. A direct energy forward method and a constant power control strategy are employed to achieve low bus voltage, high efficiency and good output characteristics. It is verified by simulation and experiment results.
Novel three-phase power factor corrector suitable for charging systems

Meng Tao,Ben Hongqi,Wang Daqing

DOI: https://doi.org/10.1109/VPPC.2008.4677419

2008-01-01

Abstract:A novel three-phase full-bridge power factor corrector is presented in this paper. The corrector operates in discontinuous conduction mode (DCM), the peak of input current follows the input voltage automatically. It can achieve zero-voltage-switching (ZVS) for the leading-leg switches and zero-current-switching (ZCS) for the lagging-leg switches without adding any auxiliary device. Due to the adoption of high frequency transformer, the electrical isolation between input and output sides and output voltage regulation could be achieved. The corrector is very suitable for charging systems. It can reduce the voltage stress of the switches of the DC/DC converters used in the later stage as well as achieve a high power factor (PF) in the input side. Some introduction and analysis about the corrector has been given. Finally, the analysis on this corrector has been verified through simulation and experiment.
Three-phase Three-level PFC Rectifier Under Single-Cycle Control

Chen Xianming,Lv Hongshui,Liu Guohua

2012-01-01

Abstract:What the paper presents first is the application of single-cycle control over anti-parallel-connection whole-control power electronic switch components of the diode of three-phase tertiary rectifier, to realize PWM control; In addition, the analysis of boost PFC topology circuit reveals that without inversion, operating only intermittent conduction control over whole-control swich components of upper bridge arm or lower bridge arm, the power factor may reach 1, so as to realize the target of AC lead-in sine-wave current. Matlab/Simulink program is applied to model and simulate three-phase tertiary rectifier PFC circuit single-cycle control, and expected results are reached, which proves that it works in principle.
Three-Phase Power Factor Correction Based on the Parallel of Single-Phase

Ben Hong-qi

2009-01-01

Abstract:The advantages of three-phase power factor correction(PFC)are obvious but it s always complicated to be realized.However,the single-phase PFC has been well developed and it is relatively easy.So,the three-phase PFC can be realized by the single-phase control method.Advantages of the realization from single-phase control to three-phase power factor correction are analyzed in this paper.Several different types of methods about using single-phase control to realize the three-phase power factor correction are introduced and corresponding circuit topologies are given.Various structures are compared,and their respective characteristics are introduced.Finally considering its merits,this method has a certain market value.
STUDY OF A THREE-PHASE POWER FACTOR CORRECTION BASED ON A SINGLE ZERO-CURRENT SWITCHING Cuk CONVERTER

邓超平,刘晓东,凌志斌,郑益慧,叶芃生

DOI: https://doi.org/10.3321/j.issn:0258-8013.2004.04.014

2004-01-01

Abstract:A three-phase high power factor rectifier based on Cuk converter is presented. A single switch and uncontrolled three-phase rectified bridges are used to obtain the high power factor and low harmonic input current. A multi-resonant operation is obtained by series with an inductor to the Cuk capacitor and shunting a small capacitor to the freewheeling diode. The principle of topology circuit is analyzed and simulation results confirm the validity of the analysis, a 2 kW experimental prototype is designed. A wide regulation capability of the output voltage, high power factor and high efficiency is obtained in this circuit. It will be a practical topology.
A Single Switch Three-Phase Power Factor Correction Based on Cuk Converter

DENG Chao-ping,LING Zhi-bin,ZHENG Yi-hui,YE Peng-sheng

DOI: https://doi.org/10.3321/j.issn:1006-2467.2005.03.020

2005-01-01

Abstract:A three-phase rectifier based on Cuk converter was presented. A single switch and uncontrolled three-phase rectified bridges are used to obtain the high power factor and low harmonic input current. A small Cuk capacitor is used to obtain the zero-current turn-on and zero-voltage turn-off of the switching. The operation principle of the circuit was analyzed. The simulation and the experimental result confirm the validity of the analysis. A wide regulation capability of the output voltage and the robustness to the load is obtained in this circuit.
Study of a New Single-phase PFC Method Based on One-cycle Control

鲁志本,张逸飞,贲洪奇

IF: 5.967

2009-01-01

IEEE Transactions on Power Electronics

Abstract:A novel bridgeless Boost PFC circuit is introduced as the main circuit of power factor correction(PFC) ,which reduces the loss due to the advantage of this topology.One-cycle control is adopted as the control mode for this circuit,which improves the output stability and the capability of continual PFC.Also the current acquisition methods are analyzed in comparison and the sampling method with hall current sensor is elaborated.The experimental results verify that the proposed PFC circuit possesses more advantages than traditional PFC circuit and can achieve the function of active power factor well.

Analysis and Improvement of Single Phase Power Factor Corrector Circuit

Study of a Single-stage Three-phase PFC DC/DC Converter With Series-parallel Connected Transforms

Design and Analysis of Single-Stage Power Factor Correction Converter with a Feedback Winding

Modeling and Controller Design of Active Power Factor Correction Based on L6562A

An Analysis of Power Factor Corrector Chip UC3854

Study on Comparison of Two Methods of Passive Three-phase Power Factor Correction

Improvement of self-oscillation circuit by single-tube induction heating

Steady-State and Dynamic Study of One-Cycle-controlled Three-Phase Power-Factor Correction

Analysis and Design Considerations of Improving Power Factor at Light-Load in a CHB Rectifier with Common-Duty Control

Single Stage PFC Circuit with Full Bridge Structure

Analysis and simulation study on single-phase H-bridge rectifier/inverter

High efficiency power factor correction power supply based on SiC device

A ZCS AC/DC CONVERTER WITH HIGH POWER FACTOR BASED ON PWM CONTROL STRATEGY

Development of Single-phase Power Factor Corrector Based on Si8250 Digital Controller

A Single-stage Power Factor Correction Converter with Constant Power Control

Novel three-phase power factor corrector suitable for charging systems

Three-phase Three-level PFC Rectifier Under Single-Cycle Control

Three-Phase Power Factor Correction Based on the Parallel of Single-Phase

STUDY OF A THREE-PHASE POWER FACTOR CORRECTION BASED ON A SINGLE ZERO-CURRENT SWITCHING Cuk CONVERTER

A Single Switch Three-Phase Power Factor Correction Based on Cuk Converter

Study of a New Single-phase PFC Method Based on One-cycle Control