Abstract:Improving the toughness of epoxy resins (EP) with diverse thermoplastic polymers through curing reaction induced phase separation (RIPS) has been widely studied, with the prerequisite of designing and tailoring the phase morphology evolution of the blend. Herein, two typical amine-type curing agents, 4,4′-diamino diphenylmethane (DDM) with precuring temperature at around 150 °C and diethylenetriamine (DETA) at 80 °C were utilized to regulate and control the phase structures of EP-poly(ε-caprolactone) (PCL) blends. The curing temperature above or below the melting temperature (Tm) of PCL resulted in different states of PCL. The effect of curing temperature on the miscibility between EP matrix and PCL phase, and the correlation between phase morphology evolution and thermomechanical behavior, mechanical properties were comprehensively investigated for the first time. Results revealed that when the curing temperature of EPDDM-PCL blends was higher than the Tm of PCL, curing took place without phase separation; while distinct phase separation took place when EPDETA-PCL was cured at a temperature below the Tm of PCL. When the curing temperature was high, the PCL was able to dissolve completely in the resin before crosslinking began, so that semi-interpenetrating networks were formed; and that when the curing temperature was low, the PCL was unable to dissolve, and therefore formed separate particles. Consequently, the EPDDM-PCL blends exhibited all-leading mechanical properties due to the entanglement and slippage between PCL chains and EP networks. The strength of EPDETA-PCL was reduced but the toughness was improved for island-shaped PCL particles bridging or pinning the cracks during failure. These results elucidated the effect of the phase morphologies formed at different curing temperature on mechanical properties, and provided significant insights regarding the toughening of thermosets.

INFLUENCE OF CURING CONDITIONS ON PHASE BEHAVIOR AND PROPERTIES OF EPOXY/ACM BLENDS

Study on the Polyethersulfone/bismaleimide Blends: Morphology and Rheology During Isothermal Curing

Studies on the Phase Separation of Poly(Ether Imide)‐Modified Cyanate Ester Resin

Molecular Dynamics Simulations of Mechanical Properties of Epoxy-Amine: Cross-linker Type and Degree of Conversion Effects

Effect Of Polyethersulfone On The Mechanical And Rheological Properties Of Polyetherimide-Modified Epoxy Systems

Viscoelastic Effects on the Phase Separation in Thermoplastics-Modified Epoxy Resin

Effects of curing temperature on the structure and properties of epoxy resin-poly(ε-caprolactam) blends

Preparation, Curing Properties, and Phase Morphology of Epoxy-Novolac Resin/multiepoxy-Terminated Low-Molecular-weight Poly(phenylene Oxide) Blend

Studies on Phase Morphology Control of Epoxy/PSF Blends

Influence of Epoxy Resin on the Morphological and Rheological Properties of PBT/ABS Blends Compatibilized by ASMA

Effects of Dynamic Crosslinking on Crystallization, Structure and Mechanical Property of Ethylene-Octene Elastomer/EPDM Blends

Mechanical Properties and Morphologies of Carboxyl-Terminated Butadiene Acrylonitrile Liquid Rubber/Epoxy Blends Compatibilized by Pre-Crosslinking

Effect of curing agents n‐octylamine and m‐xylene diamine on the mechanical and memory properties of E51 epoxy resin

Cure Kinetics of an Epoxy Resin Containing Naphthyl/dicyclopentadiene Moieties and Bis‐phenoxy (3‐hydroxy) Phosphine Oxide System and Properties of Its Cured Polymer

Mechanical Properties of Epoxy Resin/Hydroxyl-Terminated Polyester Blends: Effect of Two-Phase Structure

PHASE MORPHOLOGY CONTROL OF POLYSULFONE-MODIFIED EPOXY RESIN

Study on the self-crosslinking behavior based on polychloroprene rubber and epoxidized natural rubber

Influences of amine/epoxide ratio on cross-linking structure and mechanical properties of cured hydrogenated epoxy resin sheets and single-lap joints

Studies on Phase Separation of Polyesterimide-Modified Epoxy Resin. Ii. Effect of Curing Temperature on Phase Separation and Adhesive Property

Phase Structure Control of Epoxy/polysulfone Blends — Effects of Molecular Weight of Epoxy Resins

Phenyl Propyl Polysiloxane‐Modified Epoxy Resin III: The Reaction Condition, Phase Structures, and Macroproperties