Abstract:An investigation was conducted into the impact of low cobalt content on the microstructure and mechanical properties of titanium alloys. Ti-4Al-6Cr-5Mo-8Nb-xCo (x = 0, 2, 3, 4, and 5) alloys were prepared by ultrasonic-assisted melting and casting. The changes in microstructure, mechanical properties, and the strengthening and toughening mechanisms were researched. Results show that, when the cobalt content increases from 0 to 5wt.%, the as-cast structure is all β phase. The lattice parameter of the β phase decreases from 0.3663 to 0.3114nm, a 15% decrease. The size of primary β grains decreases from 676.8 to 310.7 μm, a 54% decrease. When the cobalt content exceeds 3wt.%, the segregation energy of cobalt increases and grain boundary segregation occurs. Grain refinement is due to constitutional supercooling caused by the β-stable element cobalt, as well as the solute drag caused by the differences in intragranular and grain boundary compositions. In addition, the size mismatch between cobalt and titanium atoms leads to lattice distortion. As the cobalt content increases from 0 to 3wt.%, the tensile strength increases from 918.1 to 1147.8MPa, a 25% increase, while the fracture toughness increases from 51.7 to 59.7MPa·m1/2, a 15% increase. At 5wt.% cobalt, the tensile strength and fracture toughness diminished to 247.5MPa and 14.8MPa·m1/2, respectively. The decrease in lattice parameters mainly lead to an increase in strength. The secondary crack leads to an increase in toughness. The decline in strength and toughness results from cobalt segregating at grain boundaries, leading to embrittlement.

Influence of cobalt phase on mechanical properties and thermal shock performance of Al2O3–TiC composites

Ultra-toughened Al2O3–TiC–Co ceramic

Effects of Co on the Microstructure Evolution and Mechanical Properties of Ti-4Al-6Cr-5Mo-8Nb Alloy by Ultrasonic Vacuum Melting

In-situ TiC/Ti composites based on Ti 2 AlC–Ti system: Reaction process, microstructure, and mechanical properties

Influence of Tungsten Carbide Particles on Resistance of Alumina Matrix Ceramics to Thermal Shock

Simultaneously Increasing the Mechanical Properties and Corrosion Resistance of B4C/Al 4 C/Al Composites Via Forming "Tio2-Al" 2-Al" Interfacial Layer

R-curve Behavior of TiC Particle Reinforced Al2O3 Composites

The Influence of Powder Characteristics on Mechanical Properties of Al2O3–TiC–Co Ceramic Materials Prepared by Co‐coated Al2O3/TiC Powders

Simultaneously Increasing the Mechanical Properties and Corrosion Resistance of B4C/Al Composites Via Forming “tio2–al” Interfacial Layer

Strength improvement and fracture mechanism in Fe40Al/TiC composites with high content of TiC

Mechanical Properties and Microstructure of Al2o3/Tial in Situ Composites Doped with Cr2o3

Fracture behaviour, microstructure, and performance of various layered-structured Al2O3-TiC-WC-Co composites

Microstructure and High-Temperature Mechanical Properties of CrMnFeCoNi/TiAl Composites Prepared by Powder Metallurgy

Reaction mechanism and microstructure evolution of superhigh strength in-situ TiC/Ti composite based on Cr 2 AlC-Ti system

Microstructure Evolution and Electromagnetic Properties Improvement of Al18B4O33w/Co Composite Powders Through Heat-Treatment

Enhanced thermal shock resistance of ZrO2-reinforced Al2O3–CaAl12O19 composites prepared from ferrotitanium slag: Crack propagation resistance mechanisms

Effect of Cobalt Addition on Thermal Cycling Behaviour of Ti50Ni(50-x)Cox Shape Memory Alloys

Effect of Al content on impact resistance behavior of Al-Ti-B4C composite fabricated under air atmosphere

Effect of Mo addition on microstructure and wear resistance of laser clad AlCoCrFeNi-TiC composite coatings

Microstructure and Mechanical Properties of Ti2AlC Particle and In-Situ TiAl3 Reinforced Pure Al Composites

Preparation and toughness mechanism of in-situ Ti<sub>3</sub>AlC<sub>2</sub> enhanced and toughened TiAl<sub>3</sub> matrix composites