Abstract:The mechanical interaction between welded panel and fixture has a remarkable influence on the distribution of weld induced residual stress and distortion.Unfortunately,the influence of fixture is not generally included in conventional numerical simulations of welding process.In the present study,it is proposed that the numerical models in which the mechanical interaction between welded panel and fixture is considered as contact pair in the finite element analysis(FEA) of welding process.This could make the FEA of welding process more scientific and accurate.The fixture constraint plays an important role in accurate modeling of welding process.In the simulations,various mechanical constraint boundary conditions in welding process were thought about to establish the relationships of the normal and tangential mechanical interactions between welded panel and fixture. In Free model,the fixture restraint was not considered.In Mech model,the displacements of nodes where welded panel contacted with fixture were restricted in x,y,z directions.Hard model and Tabular model were contact models which included the fixture.In the normal direction,once welded panel and fixture were in contact,the transmitted contact pressure could be infinite in Hard model.While data pairs of contact pressure vs over-closure or clearance were specified to define a piecewise-linear relationship in the normal direction in Tabular model.A penalty friction coefficient of 0.3 was applied in tangential direction in both Hard and Tabular models.Fixture and welded panel were separated and the contact relationships were removed after the welding process in both Hard and Tabular models. The simulation results of contact models including fixture were more accurate,compared to models containing only welded panel with rigid restrictions.The distortion mode of welded panels under different fixture constraint conditions corresponded well with experimental results.The differences between the distributions of transverse stresses on top and bottom surfaces of welded panel at the beginning of welding process had a crucial influence on the distortion mode of welded panel.

Numerical Study on the Effectiveness of Fixture and Pre-Strain for Reduction of Welding Distortion

Numerical simulation about the effect of fixture on the welding stress and distortion of thin aluminum plate joints

Study on FEM Numerical Simulation Method for the Welding Distortion

ESTABLISHMENT AND APPLICATION OF FIXTURE CONSTRAINT MODELS IN FINITE ELEMENT ANALYSIS OF WELDING PROCESS

Numerical Analysis on Optimizing Welding Sequence of Large-Sized Bottom Structure for Controlling Welding Distortion

Prediction of distortion in a thin-plate structure with intermittent fillet joints using a local-to-global approach

Determination of Welding Stress and Distortion in Discontinuous Welding by Means of Numerical Simulation and Comparison with Experimental Measurements

Welding-induced stresses and distortion in high-strength steel T-joints: Numerical and experimental study

Accuracy of computational welding mechanics methods for estimation of angular distortion and residual stresses

Welding Distortion Prediction In 5a06 Aluminum Alloy Complex Structure Via Inherent Strain Method

Investigation of Inherent Deformation in Fillet Welded Thin Plate T-joints Based on Interactive Substructure and Inverse Analysis Method

Controlling of Welding Residual Stress and Deflection Distortion for Flat Plate by Longitudinal Pre-stress Method

Review on finite element analysis of welding deformation and residual stress

Numerical Simulation of Welding Stresses and Distortions Based on 3D Dynamic Substructure Method

Predicting Residual Distortion of Aluminum Alloy Stiffened Sheet after Friction Stir Welding by Numerical Simulation

Effect of Elastic Pre-Bending on Mitigating Welding Deformation for Aluminium Alloy Thick-Walled Plates Joined by FSW

Numerical Simulation and Testing of Dynamic Welding Angular Distortion for Overlayer

The Deformation Analysis of Friction Stir Welding with Different Clamping Distances for Large Thin-Walled Joints

Numerical Simulation of Weld Tab Length Influence on Welding Residual Stress and Distortion of Aero-Engine Disk

Comparative Study of Welding Deformation of a Stiffened Panel under Various Welding Procedures

Investigating Welding Distortion of Thin-Plate Stiffened Panel Steel Structures by Means of Thermal Elastic Plastic Finite Element Method