Abstract:The solid/gas eutectic unidirectional solidification process is a new kind of technology fabricating the lotus-type porous structure. Besides having the properties of large specific surface area, excellent sound absorption, penetrating performance etc. of traditional porous materials, the particularity of the lotus-type porous structure makes it has extraordinary mechanical and thermal properties. There is a great potential for lotus-type porous aluminum in the field of lightweight engineering and heat dissipation of chip owing to its low density, outstanding corrosion resistance and high thermal conductivity. However, the fabrication of lotus-type porous aluminum has always been been more difficulty than other metals. Until porous aluminum with excellent pore structure was fabricated under very small solidification rates (0.008 similar to 0.015 mm/s) and high superheat degrees of melt (240 similar to 340 K), the proper processing parameters were recognized to be essential for the coupled growth of solid/gas phases for Al-H-2 system, especially the solidification rate. In this work, a three-dimensional time-dependent model describing the evolution of single pore was established based on the theoretical analysis of mass transfer, gas bubble nucleation, pore growth, interruption and detachment. The morphology of single pore under different solidification rates were simulated during the Gasar process by using the finite difference method for Al-H-2 system. The research reveals: coupled growth of solid/gas phases can be achieved under the solidification rates from 0.15 mm/s to 0.005 mm/s. The average pore diameter which ranges from 100 pm to 1100 pm increases with decreasing the solidification rate. The pore length also increases while the pore aspect ratio is nearly a constant about 40 with decreasing the solidification rate. The simulated average pore diameter is in good agreement with the experimental values when solidification rate equals to 0.015 mm/s, and then being slightly lower than the experimental ones with decreasing the solidification rate. The diffusion of hydrogen into the melt during the solidification process is regarded as the main reason of the discrepancy between simulated and experimental average pore diameters. The maximum value of the simulated solidification rates for coupled growth of solid/gas phases in Al-H-2 system first increases from less than 0.01 mm/s to 0.15 mm/s and then being a constant, while the minimum ones increase from about 0.0001 mm/s to 0.01 mm/s with improving the overheat degree of melt and hydrogen partial pressure. By comparing the relative parameters of Al-H-2 and Cu-H-2 systems, the solubility of hydrogen is regarded to be the main parameter which determines solidification rates of coupled growth of solid/gas phases for Al-H-2 system.

Experimental Study on the Pore Structure of Directionally Solidified Porous Cu-Mn Alloy

Influence of Solidification Mode on Pore Structure of Directionally Solidified Porous Cu-Mn Alloy

Influence of the Solidification Temperature Range on Gasar Structures Made from Cu–Mn Alloys

Effect of the Solidification Mode on the Pore Growth of Gasar Porous Mg‐Ag Alloy

Directionally Solidified Porous Metals: A Review

Directional Solidification of Metal-Gas Eutectic and Fabrication of Regular Porous Metals

Numerical simulation of microstructure and microporosity morphology in directional solidification of aluminum-copper alloys: Effect of copper content and withdrawal rate

Influence of Initial Solid–liquid Interface Morphology on Further Microstructure Evolution During Directional Solidification

Metal-Gas Eutectic Growth During Unidirectional Solidification

Preparation and Microstructure Analysis of Continuous Unidirectional Solidification Cu–P–Sn Alloy

The Effect of Wettability on Gas Porosity Formation During Directional Solidification of Alloys: Insights from Lattice Boltzmann-cellular Automata Simulations

Microstructure Evolution of Cu-Pb Monotectic Alloys During Directional Solidification

Effects of specimen dimensions on directional solidification microstructure and interface stability of Al-4.5%Cu alloy

Effect of directional solidification and porosity upon the superelasticity of Cu–Al–Ni shape-memory alloys

MODELING AND SIMULATION OF STRUCTURAL FORMATION OF POROUS ALUMINUM IN GASAR SOLIDIFICATION

The pore growth process and pore coalescence process in Gasar copper

Microstructure evolution, Cu segregation and tensile properties of CoCrFeNiCu high entropy alloy during directional solidification

Pore structure of porous Mg-1Mn-xZn alloy fabricated by metal–gas eutectic unidirectional solidification

Directional Solidification of Undercooled Hypoeutectic Silver-Copper Alloy Melt

Fabrication of a Three-Dimensional Bimodal Porous Metal

Multiphase-field Modelling of Hydrogen Pore Evolution During Alloy Solidification