Abstract:Chemical-mechanical planarization (CMP) represents the preferred technology in which both chemical and mechanical interactions are combined to achieve global planarization/polishing of wafer surfaces (wafer patterns from metal with a selective layer, in this paper). CMP is a complex process of material removal process by friction, which interferes with numerous mechanical and chemical parameters. Compared with chemical parameters, mechanical parameters have a greater influence on the material removal rate (MRR). The mechanical parameters manifest by friction force (Ff) and heat generated by friction in the CMP process. The Ff can be estimated by its monitoring in the CMP process, and process temperature is obtained with help of an infrared rays (IR) sensor. Both the Ff and the MRR increase by introducing colloidal silica (SiO2) as an abrasive into the selective layer CMP slurry. The calculated wafer non-uniformity (WNU) was correlated with the friction coefficient (COF). The control of Ff and of the slurry stability is important to maintain a good quality of planarization with optimal results, because Ff participates in mechanical abrasion, and large Ff may generate defects on the wafer surface. Additionally, the temperature generated by the Ff increases as the SiO2 concentration increases. The MRR of the selective layer into the CMP slurry showed a non-linear (Prestonian) behavior, useful not only to improve the planarization level but to improve its non-uniformity due to the various pressure distributions. The evaluation of the Ff allowed the calculation of the friction energy (Ef) to highlight the chemical contribution in selective-layer CMP, from which it derived an empirical model for the material removal amount (MRA) and validated by the CMP results. With the addition of abrasive nanoparticles into the CMP slurry, their concentration increased and the MRA of the selective layer improved; Ff and MRR can be increased due to the number of chemisorbed active abrasive nanoparticles by the selective layer. Therefore, a single abrasive was considered to better understand the effect of SiO2 concentration as an abrasive and of the MRR features depending on abrasive nanoparticle concentration. This paper highlights the correlation between friction and temperature of the SiO2 slurry with CMP results, useful to examine the temperature distribution. All the MRRs depending on Ef after planarization with various SiO2 concentrations had a non-linear characteristic. The obtained results can help in developing a CMP process more effectively.

Investigating Effect of Conditioner Aggressiveness on Removal Rate During Interlayer Dielectric Chemical Mechanical Planarization Through Confocal Microscopy and Dual Emission Ultraviolet-Enhanced Fluorescence Imaging

Characterization of Pad–Wafer Contact Area and Distance in Chemical-Mechanical Polishing

Improvement and Application of Pad Conditioning Accuracy in Chemical Mechanical Polishing

Analysis on Pad Effects in Chemical Mechanical Polishing

Modeling and Experimental Analysis of the Material Removal Rate in the Chemical Mechanical Planarization of Dielectric Films and Bare Silicon Wafers

Modeling the microscale contact status in chemical mechanical polishing process

Characterization of Pad–Wafer Contact and Surface Topography in Chemical Mechanical Planarization Using Laser Confocal Microscopy

Chemical mechanical polishing: Theory and experiment

The Deterioration Characteristics and Mechanism of Polishing Pads in Chemical Mechanical Polishing of Fused Silica

Impact of Pad Conditioning on the Bonnet Polishing Process

Impact of Pad–Wafer Contact Area in Chemical Mechanical Polishing

Factors influencing the dressing rate of chemical mechanical polishing pad conditioning

Effects of the Polishing Variables on the Wafer-Pad Interfacial Fluid Pressure in Chemical Mechanical Polishing of 12-Inch Wafer

Effect of Slurry Injection Position on Material Removal in Chemical Mechanical Planarization

Optical and Mechanical Characterization of Chemical Mechanical Planarization Pad Surfaces

Material Removal Regions in Chemical Mechanical Planarization for Submicron Integrated Circuit Fabrication: Coupling Effects of Slurry Chemicals, Abrasive Size Distribution,and Wafer-Pad Contact Area

Effects of grinding-induced surface topography on the material removal mechanism of silicon chemical mechanical polishing

Energy dissipation and constitutive modeling for a mechanistic description of pad scratching in chemical–mechanical planarization

The Effects of Friction and Temperature in the Chemical-Mechanical Planarization Process

Micro-scale contact behavior and its effect on the material removal process during chemical mechanical polishing

Wear phenomena in chemical mechanical polishing