Abstract:The class of NbC-Ni cermets has emerged as a promising environmentally friendly alternative to WC-Co cemented carbide tools, although some inherent properties i.e. room temperature hardness and flexural strength, of NbC-Ni cermets may require further enhancements. To enhance the properties of NbC-Ni cermets, diverse methodologies were applied, including grain inhibition and the strengthening of the cermet through the use of reinforcements. This study systematically examined the impact of TiC additions, specifically at 10% and 20%, on both the microstructure and mechanical properties of NbC-12Ni-4VC-4Mo2C cermets. NbC-12Ni cermets were fabricated via vacuum liquid phase sintering (LPS) at 1400°C and 1450°C. Enhancements by incorporating 4% VC and 4% Mo2C, followed by TiC at 10% and 20% concentrations to the NbC-Ni-4VC4Mo2C cermet were made. XRD and SEM results confirm the formation of (Nb, X, Y) C solid solution cubic FCC carbides. Significant grain refinement was evident in the cermet samples, subjected to grain inhibition. The observed grain sizes ranged from a maximum of 6.84 μm (in NbC12Ni) to a minimum of 2.154 μm (in the sample containing 20% TiC) at 1450°C. The incorporation of 20TiC at 1450°C led to a remarkable 26.5% enhancement in average hardness compared to NbC-Ni cermet, and a 4.2% improvement over the 4VC4Mo2C cermet. At 1450°C, 20TiC reinforcement led to an average fracture toughness of 9.331 MPa√m, representing a 4.56% improvement over the 4VC4Mo2C cermet. However, there was a marginal reduction in toughness compared to the NbC-Ni cermet. Moreover, the addition of TiC led to a decrease in the flexural strength of the cermets, with a maximum flexural strength of 939 N/mm2 recorded for NbC-Ni-4VC4Mo2C, representing an 11.6% increase compared to the NbC-Ni cermet.

The microstructure of (Nb,Ti)C-35Ni(Y2O3) cermet

Microstructure and mechanical properties of (nb, ti)c-nickel base superalloy

Microstructure and Mechanical Properties of TiC Reinforced NbC-Ni4VC4Mo2C Cermets

Influence of hot-pressure technology on the mechanical properties of Ti(C,N) based cermet

Fabrication, microstructure evolution, and mechanical properties of Ti(C,N)-HfN-WC-Ni-Mo cermets

The Flexural Strength at High Temperature and Oxidation Behaviour of (nb,ti)cni Composite

The investigation on the fabrication and microstructure of NbTi-(NbTi)C Fe-based composite

Formation of solid solution structures in (Ti,W,Ta,Mo)(C,N) cermet via spark plasma sintering

Microstructure and strengthening mechanism of Mo@Ni reinforcement (W,Ti)C cermet via spark plasma sintering

Evolution of microstructure and interfacial characteristics of complete solid-solution Ti(C,N)-based cermets fabricated by mechanical activation and subsequent in situ carbothermal reduction

Study on Microstructures and Properties of Porous TiC Ceramics Fabricated by Powder Metallurgy

MICROSTRUCTURE AND MECHANICAL PROPERTIES OF NANO MODIFIED CERMETS

Novel Α/β SiC-(Ti, Nb)B2 Toughened (ti, Nb)C-based Composites with Enhanced Mechanical Properties Fabricated by in Situ Reactions Sintering at Low Temperature

MICROSTRUCTURE AND MECHANICAL PROPERTIES OF (Nb,Ti)C-Ni COMPOSITE

Effect of Y2O3 Addition on the Microstructure and Mechanical Properties of TiCN-based Cermets

Tuning microstructure for superb mechanical properties in a Ti(C,N)-(WMoTaNbTi)C-Ni/Co cermets via change sintering temperature

Microstructure, mechanical properties and thermal conductivity of (Ti0.5Nb0.5)C–SiC composites

Improvement in Microstructure and Mechanical Properties of Ti(C, N) Cermet Prepared by Two-Step Spark Plasma Sintering

Multiwalled Carbon Nanotubes–TiB2–Ni Composite: Microstructure and Mechanical Properties

Influence of TaC content on microstructure and mechanical performance of Ti(C,N)-based cermets fabricated by mechanical activation and subsequent in situ carbothermal reduction

Effect of Boronizing on Microstructure and Properties of Ti（ C, N）-based Cermet