Abstract:The flow condensation heat transfer coefficient of R134a inside two helical micro-fin tubes with outer diameter of 6.35 mm and helical angles of 18o and 28o respectively were experimentally studied at a high mass flux ranging from 500 to 1100 kg m−2 s−1. The condensation temperatures are 35°C, 40°C and 45°C, and the vapor qualities ranges from 0.95 to 1.00 at the inlet section and from 0.00 to 0.05 at the outlet section. Experimental results show that there are annular and intermittent flow regimes inside the tube under experimental conditions, the ratio of annular flow region to the total heat transfer region is about 70%. The liquid film flow changes from rotational flow to coexistence of rotational and horizontal flows when the vapor quality is 0.475±0.08, 0.486±0.06 and 0.521±0.05, respectively and the corresponding saturation temperature is 35°C, 40°C and 45°C. Based on the experimental data, the heat transfer coefficient increases with increasing mass flux and fin helical angle, and with decreasing saturation temperature and Reynolds number of cooling water. In addition, the heat transfer coefficient of annular flow is greater than that of intermittent flow, in other words, the heat transfer coefficient increases with increasing vapor quality. The heat transfer coefficient obtained at high mass flux was compared with the calculated data of some published correlations used at low mass flux. It was found that most correlations underestimate the experimental heat transfer coefficient inside the micro-fin tube, and these prediction deviation increases with increasing mass flux and fin helical angle. By introducing some dimensionless numbers as well as considering the flow mechanism of liquid film inside the tube, two heat transfer coefficient correlations were proposed based on the experimental data. The ratio of liquid film thickness to fin height was used to characterize whether the liquid film flow is rotational flow or coexistence of rotational and horizontal flows in the proposed correlation, which shows a better prediction accuracy with a mean deviation of less than 7.3%.

Boiling Heat Transfer Correlations for Refrigerant Mixtures Flowing Inside Micro-Fin Tubes

A New Heat Transfer Model for Flow Boiling of Refrigerants in Micro-Fin Tubes

Study on Flow Boiling Heat Transfer Characteristics of R161/oil Mixture Inside Horizontal Micro-Fin Tube

Experimental Study of Condensation Heat Transfer of R134a Inside the Micro-Fin Tubes at High Mass Flux

Heat Transfer Correlations for Single-Phase Flow, Condensation, and Boiling in Microfin Tubes

Saturated Flow Boiling Heat Transfer of R1233zd(E) in Parallel Mini-Channels: Experimental Study and Flow-Pattern-based Prediction

Investigating the Thermal-Hydraulic Performance of New Refrigerant Mixtures Through Numerical Simulation of Minichannel and Microchannel Evaporators

Visualization of R1233zd(E) Flow Boiling in Parallel Mini-channels

Theoretical and Experimental Analyses of Two-Phase Flow Condensation Heat Transfer Inside the Horizontal Micro-Fin Tube

Flow boiling heat transfer characteristics and correlation development of R290/R600a mixtures in an internally threaded tube{fr}Caractéristiques de transfert de chaleur par ébullition en écoulement et développement de corrélations pour les mélanges R290/R600a dans un tube fileté interne

Study on Flow Boiling of Refrigerants in Micro/Mini-Channels

Experimental investigation on flow boiling heat transfer of R290, R600a and their mixtures in a horizontal minichannel

Boiling Heat Transfer and Visualization for R717 in a Horizontal Smooth Mini-tube

Frictional Pressure Drop During Flow Boiling in Micro-Fin Tubes: A New General Correlation

Evaluation of Frictional Pressure Drop Correlations During Flow Boiling of Refrigerants in Micro-Fin Tubes

Two-Phase Flow Heat Transfer In Micro-Fin Tubes

Single Phase And Two Phase Flow Characteristics And Heat Transfer In Micro-Fin Tubes

A General Correlation for Saturated Two-Phase Flow Boiling Heat Transfer Inside Horizontal and Vertical Tubes

Flow Boiling Heat Transfer Characteristics in Horizontal, Three-Dimensional Enhanced Tubes

A General Correlation for Condensation Heat Transfer in Micro-Fin for Herringbone and Dimple-Texture Tubes

An Experimental Study of R410A Condensation Heat Transfer and Pressure Drops Characteristics in Microfin and Smooth Tubes with 5 Mm OD