Abstract:Condenser is a huge,complex shell-and-tube heat exchanger.It is the key auxiliary equipment in power plants whose designs have a very important influence on thermal efficiency of electric power generation.At present,power plant condensers are traditionally designed based on recommendations from previous designs and experimental results,often based on the standards developed by the Heat Exchange Institute.However,it does not take a number of factors into account,including the tube arrangement.Hence,to study the tube arrangement effect on condenser performance and to optimize/improve the condenser design are very important for energy saving.The condenser performances,such as the back pressure and venting rate,are strongly affected by the tube arrangement,and there are three irreversible processes for the fluid flow,heat transfer and mass diffusion in condenser.Borrowing from the entransy analysis method of heat transfer process,the momentum entransy analysis and mass entransy analysis were performed on the steam flow and air mass diffusion process in condenser.Adopting the porous media model the momentum entransy balance equation and the air mass entransy balance equation of the steam flow were deduced,then,the relation of momentum entransy loss of the steam flow and the distributed flow and heat transfer parameters in the condenser and the relation of air mass entransy increase of the steam flow and the distributed parameters of flow,heat transfer and air mass fraction were deduced.With the two relations the effects of tube arrangement on the back pressure and the venting rate are numerically investigated.The numerical analyses on four typical condensers indicate that larger momentum entransy loss relates to larger back pressure,and larger air mass entransy increase relates to less venting rate.Based on the numerical results of the four kinds of tube arrangements 330 MW condensers,the principles for tube layout in condenser are summarized.For examples,the reasonable design of the periphery of the tube bundle,i.e.,the tube bundle profile,can lead the steam more uniformly entering the tube bundle,then the back pressure can be decreased;the tube arrangement should be well designed to properly guide the steam flow so as to avoid vortex flows,and a air cooling region should be well designed to reduce the venting rate.Finally,the bionic double-tree-shaped tube bundle condenser is introduced and the performances of a 330 MW condenser with bionic double-tree-shaped tube bundle are numerically analyzed.The results indicate that the steam uniformly enters the tube bundle,the thermal parameters are mainly centripetally distributed from the tube bundle periphery to the venting channel;the well-designed auxiliary steam entering channels result in a reduction of average steam velocity,hence,a reduction of flow resistance;The non-condensed steam is deeply condensed in the gradually contracted air cooling region,which strongly reduces the venting rate.Compared with the existing four kinds of condensers,its flow and thermal performances are much better.The back pressure of the rebuilt #2 condenser of Laicheng Power Plant by using the bionic double-tree-shaped tube bundle is decreased 1.5 kPa.

Commercial and Experimental Study of a Rotor-assembly Type Intensified Heat-transfer Device at the Tube Side

Experimental investigation on DC flow suppression and refrigeration characteristics of a high-performance single-stage GM-type

Technical Performance and Cost-effectiveness of Gas Turbine Inlet Air Cooling Systems

Experimental Study of the Condensation Heat Transfer Performance of Flue Gases in a Heating-and-power Cogeneration System

Experimental study of the mechanism governing the HAT (humid air turbine) cycle performance of a split-shaft micro gas turbine

Heat-Transfer Performance-Test Of A Prototype Plate-Fin Condenser-Boiler For Industrial Usage

Optimization Design and Comparative Analysis of Enhanced Heat Transfer and Anti-Vibration Performance of Twisted-Elliptic-Tube Heat Exchanger: A Case Study

Experimental Study on Thermal–hydraulic Performance of Moist Air Inside Flat Tube of Two Kinds of Plate-Fin Heat Exchangers

Experimental Study Of Water Cooled Condenser Made Of Three Dimensional And High Fin Density Integral-Finned Tubes

Theoretical and Experimental Studies for a Transcritical CO2 Heat Pump with Spirally Fluted Tube Gas Cooler

A Comparative Study on Coupled Fluid–Thermal Field of a Large Nuclear Turbine Generator with Radial and Composited Radial–Axial–Radial Ventilation Systems

Entransy Analysis of Tube Arrangement Effect on Condenser Performances and Its Application

An Experimental Investigation on Air-Side Performances of Finned Tube Heat Exchangers for Indirect Air-Cooling Tower

The Cooling Performance Evaluation Of A Micro-Trigeneration System

Analysis of energy consumption on EHD enhancement of condensation heat transfer inside tube

Experimental study of a novel in-tube spray evaporative condenser for geothermal power generation

Study on heat transfer and water saving characteristics of a new cooling tower condensation module

Experimental analysis of a novel gas-engine-driven heat pump (GEHP) system for combined cooling and hot-water supply

Effect of gas turbine intake air temperature regulating heat exchanger on combined cycle performance based on three-dimensional deformed tube

Thermo-Flow Performances for the Main-Auxiliary Integrated Natural Draft Dry Cooling System

Experimental Analysis on Domestic Air-conditioning Condense Heat Recovery Hot Water Supply System