Abstract:The Hall–Petch relationship, according to which the strength of a metal increases as the grain size decreases, has been reported to break down at a critical grain size of around 10 to 15 nanometres<sup><a href="/articles/s41586-020-2036-z#ref-CR1">1</a>,<a href="/articles/s41586-020-2036-z#ref-CR2">2</a></sup>. As the grain size decreases beyond this point, the dominant mechanism of deformation switches from a dislocation-mediated process to grain boundary sliding, leading to material softening. In one previous approach, stabilization of grain boundaries through relaxation and molybdenum segregation was used to prevent this softening effect in nickel–molybdenum alloys with grain sizes below 10 nanometres<sup><a href="/articles/s41586-020-2036-z#ref-CR3">3</a></sup>. Here we track in situ the yield stress and deformation texturing of pure nickel samples of various average grain sizes using a diamond anvil cell coupled with radial X-ray diffraction. Our high-pressure experiments reveal continuous strengthening in samples with grain sizes from 200 nanometres down to 3 nanometres, with the strengthening enhanced (rather than reduced) at grain sizes smaller than 20 nanometres. We achieve a yield strength of approximately 4.2 gigapascals in our 3-nanometre-grain-size samples, ten times stronger than that of a commercial nickel material. A maximum flow stress of 10.2 gigapascals is obtained in nickel of grain size 3 nanometres for the pressure range studied here. We see similar patterns of compression strengthening in gold and palladium samples down to the smallest grain sizes. Simulations and transmission electron microscopy reveal that the high strength observed in nickel of grain size 3 nanometres is caused by the superposition of strengthening mechanisms: both partial and full dislocation hardening plus suppression of grain boundary plasticity. These insights contribute to the ongoing search for ultrastrong metals via materials engineering.

Strengthening of Nickel Deformed by High Pressure Torsion

Evolution of microstructural parameters and flow stresses toward limits in nickel deformed to ultra-high strains

Influence of Processing Parameters on the Mechanical Properties of HPT-Deformed Nickel Carbon Nanotube Composites

Influence of grain shape and orientation on the mechanical properties of high pressure torsion deformed nickel

Strain-Hardening Stages and Structure Evolution in Pure Niobium and Vanadium upon High Pressure Torsion

Strength enhancement of an aluminum alloy through high pressure torsion

The nanoscale mechanisms of strengthening and ductility enhancement in an Al–Mg–Si–Mn alloy on processing by high-pressure torsion

The Effects of Severe Torsion on Microstructure, Texture, and Mechanical Properties of a Pure Nickel Rod

Insight into Elongation and Strength Enhancement of Heat-Treated LPBF Ni-based Superalloy 718 Using In-Situ SEM-EBSD

The Evolutions of Microstructure, Texture and Hardness of A1050 Deformed by HPT at the Transition Area

The Evolvement of Mechanical Properties and Microstructure of Commercial Aluminum Alloy 6061 via High-Pressure Torsion

Anomalous hot deformation behavior and microstructure evolution of as-cast martensitic NiTi alloy during hot compression

High-pressure strengthening in ultrafine-grained metals

Microstructure Evolution during High-Pressure Torsion in a 7xxx AlZnMgZr Alloy

Effects of Severe Plastic Deformation and Subsequent Annealing on Microstructures of a Ni50.6Ti49.4 Shape Memory Alloy

Severe plastic deformation of two-phase TiNiCuNb shape memory alloy

On the reinforcement homogenization in CNT/metal matrix composites during severe plastic deformation

Nano-scale Reinforcements and Properties of Al-Si-Cu Alloy Processed by High-Pressure Torsion

EFFECT OF HIGH PRESSURE TORSION ON STRUCTURE AND MECHANICAL PROPERTIES OF Al–Ca–Cu ALLOY

Strain-induced grain evolution of pure nickel under warm power torsional rolling process

Evaluating High Pressure Torsion Scaleup