Abstract:Cu-ZnO-Al2O3 is the most widely applied catalyst for CO2 hydrogenation to methanol. However, it is still a challenge to produce methanol using this catalyst under low-temperature (<250 °C) and low-pressure (<10 bar) conditions with desirable yield and selectivity. In this work, by tuning the experimental processing parameters such as solvent, loading amount, and annealing temperature, highly improved ZnO nanoarray supported Cu-ZnO-Al2O3 catalysts have been successfully demonstrated. By using organic solvent (N,N-dimethylformamide (DMF), acetone, or isopropanol) for dip-coating loading process instead of deionized (DI) water, Cu-ZnO-Al2O3 nanocatalysts was comparatively better dispersed on the nanorod array support with populated and abundant active sites, thus enhancing the methanol yield. With the control of the loading amount and annealing temperature, finely distributed Cu nanoparticles were obtained on the ZnO nanorod surfaces to enhance the interactions between Cu and ZnO nanorod surfaces. Further improvement of the catalyst performance is demonstrated by tuning the reaction space velocity. At 200 °C and 10 bar conditions, the optimized catalyst achieved a methanol yield of 6.46 mol h−1 kg−1 with 100 % selectivity. The good stability after prolonged testing of the catalysts demonstrates the potential practical implementation. The in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) measurements under the 1 bar reveal that the CO2 hydrogenation to methanol on the ZnO nanoarray supported Cu-ZnO-Al2O3 catalyst follows the CO reaction pathway, due to the surface oxygen vacancies on ZnO nanorods which facilitate CO2 dissociation.

OPTIMIZATION OF Cu/ZnO/Al2O3 CATALYST COATINGS

On-Board Production of Hydrogen for Fuel Cells over Cu/Zno/Al2o3 Catalyst Coating in A Micro-Channel Reactor

Effects of reaction progress in microchannel on microstructure of Cu-Zn catalyst

Microstructure Characters of Cu/ZnO Catalyst Precipitated Inside Microchannel Reactor

An Innovative Micro-Channel Catalyst Support with a Micro-Porous Surface for Hydrogen Production Via Methanol Steam Reforming

Influence of mixing inside microreactor on microstructural evolution of Cu-ZnO catalyst

Development of a microchannel reactor concerning steam reforming of methanol

Development of Centrifugal Coating Device to Load CuZnZr/γ-Al2O3 Catalyst on Porous Substrates for Methanol Steam Reforming

High-performance Cu/ZnO Catalysts Prepared Using a Three-Channel Microreactor

Reaction Intrinsic Kinetics of Methanol Steam Reforming over Cu/ZnO/CeO2/Al2O3 Catalyst Coatings

Hydrogen Production Via Steam Reforming of Methanol on Cu/ZnO/Al2O3 Catalysts: Effects of Al2O3 Precursors

Dissecting ZnO X /Cu interfacial self-encapsulation and methanol-induced strong metal-support interaction of the highly active alloyed CuZn and ZnO for methanol steam reforming

Cu/ZnO/Al2O3 Catalyst Modulated by Zirconia with Enhanced Performance in CO2 Hydrogenation to Methanol

In-situ Self-Assembled Cu2O/ZnO Core-Shell Catalysts Synergistically Enhance the Durability of Methanol Steam Reforming

Optimization and understanding of ZnO nanoarray supported Cu-ZnO-Al2O3 catalyst for enhanced CO2 -methanol conversion at low temperature and pressure

Modulation of Al2O3 and ZrO2 composite in Cu/ZnO-based catalysts with enhanced performance for CO2 hydrogenation to methanol

Comparative Surface Studies of High-Zn-level and Commercial Cu/ZnO/Al<sub>2</sub>O<sub>3</sub>Catalysts

A Well-Dispersed Catalyst on Porous Silicon Micro-Reformer for Enhancing Adhesion in the Catalyst-Coating Process

High-Performance Cu/ZnO/Al 2 O 3 Catalysts for CO 2 Hydrogenation to Methanol

A Monolith CuNiFe/γ-Al2O3/Al Catalyst for Steam Reforming of Dimethyl Ether and Applied in a Microreactor

Efficient Fischer–Tropsch microreactor with innovative aluminizing pretreatment on stainless steel substrate for Co/Al 2 O 3 catalyst coating