Abstract:Binary Cu/ZnO catalysts (with a Cu/Zn atomic ratio of 50/50) prepared via a novel dry synthetic approach based on solid-state oxalate-precursor synthesis were studied in regard to their performance in the steam reforming of methanol (SRM). The synthesis route involves facile solid-phase mechanochemical activation of a physical mixture of simple copper/zinc salts and oxalic acid, followed by calcination of the as-ground oxalate precursors at 350 °C. For comparison, their conventional analogues obtained by aqueous coprecipitation techniques were also examined. Structural characterization of the samples was performed by means of N2 adsorption, X-ray diffraction (XRD), diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS), thermal gravimetric and differential thermal analysis (TG/DTA), scanning electron microscopy (SEM), temperature-programmed reduction (H2-TPR), N2O titration, and X-ray photoelectron spectroscopy (XPS). The results show that the grinding-derived Cu/ZnO catalysts exhibit superior SRM performance to their conventional counterparts obtained by wet-chemical methods. The enhanced performance of the grinding-derived catalysts can be attributed to a higher copper dispersion as well as the beneficial generation of highly strained Cu nanocrystals in the working catalyst. It is proposed that the present soft reactive grinding route based on dry oxalate-precursor synthesis can allow the generation of a new type of Cu/ZnO materials with favorable surface and structural properties, providing an attractive alternative for preparation of improved heterogeneous catalysts.

High-performance Cu/ZnO Catalysts Prepared Using a Three-Channel Microreactor

Microstructure Characters of Cu/ZnO Catalyst Precipitated Inside Microchannel Reactor

Effects of reaction progress in microchannel on microstructure of Cu-Zn catalyst

Influence of mixing inside microreactor on microstructural evolution of Cu-ZnO catalyst

The Effect of Mixing on Co‐precipitation and Evolution of Microstructure of Cu‐ZnO Catalyst

Advantage of Microreactor on the Synthesis of High-Activity Cu-Mn Catalyst by Co-Precipitation

Effect of Water Layer in a Microreactor on the Low-Temperature Synthesis of High-Activity Cu/ZnO Catalysts

Strong Cu/ZnO Interfacial Interaction Induced by ZrO2 Promoter Suppressing the Ethanol Formation in Industrial Methanol Synthesis

CO2 Hydrogenation to Methanol over Cu/ZnO Catalysts Synthesized Via a Facile Solid-Phase Grinding Process Using Oxalic Acid

Preparation of High Performance Cu/Zno/Al2o3 Catalyst for Methanol Synthesis from Co2 Hydrogenation by Coprecipitation-Reduction

Synthesis of a Cu@ZnO1-x/Al2O3 Catalyst with High-Density ZnO1-x-Cu Interfacial Sites for Enhanced CO2 Hydrogenation to Methanol

Synthesis, characterization and activity pattern of Cu–ZnO/ZrO2 catalysts in the hydrogenation of carbon dioxide to methanol

Comparative Surface Studies of High-Zn-level and Commercial Cu/ZnO/Al<sub>2</sub>O<sub>3</sub>Catalysts

A High Activity Cu/ZnO/Al2O3 Catalyst for Methanol Synthesis: Preparation and Catalytic Properties

Hydrolysis Precipitation Method for the Preparation of Cu‐ZnO@Al2O3 Catalyst in Methanol Steam Reforming

Highly effective methanol steam reforming Cu/ZnO catalyst prepared by a dry mechanochemical approach based on oxalate precursor synthesis

Preparation of Cu-based Catalysts for Methanol Synthesis in a Fluidized Bed Reactor and Their Performance

A practical approach for the preparation of high activity Cu/ZnO/ZrO2 catalyst for methanol synthesis from CO2 hydrogenation

Aerosol-assisted synthesis of mesoporous Cu/ZnO-ZrO2 catalyst with highly selective photothermal CO2 reduction to methanol

Production of hydrogen by steam reforming of methanol over Cu/ZnO catalysts prepared via a practical soft reactive grinding route based on dry oxalate-precursor synthesis

Surface Properties of CuO/ZnO/Al_2O_3 Catalyst for Methanol Synthesis in Slurry Reactor