Abstract:Steels with sub-micrometre grain sizes usually possess high toughness and strength, which makes them promising for lightweighting technologies and energy-saving strategies. So far, the industrial fabrication of ultrafine-grained (UFG) alloys, which generally relies on the manipulation of diffusional phase transformation, has been limited to steels with austenite-to-ferrite transformation<a href="#ref-CR1">1</a>,<a href="#ref-CR2">2</a>,<a href="/articles/s41586-021-03246-3#ref-CR3">3</a>. Moreover, the limited work hardening and uniform elongation of these UFG steels<a href="/articles/s41586-021-03246-3#ref-CR1">1</a>,<a href="/articles/s41586-021-03246-3#ref-CR4">4</a>,<a href="/articles/s41586-021-03246-3#ref-CR5">5</a> hinder their widespread application. Here we report the facile mass production of UFG structures in a typical Fe–22Mn–0.6C twinning-induced plasticity steel by minor Cu alloying and manipulation of the recrystallization process through the intragranular nanoprecipitation (within 30 seconds) of a coherent disordered Cu-rich phase. The rapid and copious nanoprecipitation not only prevents the growth of the freshly recrystallized sub-micrometre grains but also enhances the thermal stability of the obtained UFG structure through the Zener pinning mechanism<a href="/articles/s41586-021-03246-3#ref-CR6">6</a>. Moreover, owing to their full coherency and disordered nature, the precipitates exhibit weak interactions with dislocations under loading. This approach enables the preparation of a fully recrystallized UFG structure with a grain size of 800 ± 400 nanometres without the introduction of detrimental lattice defects such as brittle particles and segregated boundaries. Compared with the steel to which no Cu was added, the yield strength of the UFG structure was doubled to around 710 megapascals, with a uniform ductility of 45 per cent and a tensile strength of around 2,000 megapascals. This grain-refinement concept should be extendable to other alloy systems, and the manufacturing processes can be readily applied to existing industrial production lines.

Ultra-Fine Ferrite Grains Obtained in the Tsdr Process

Strain-induced Refinement and Thermal Stability of a Nanocrystalline Steel Produced by Surface Mechanical Attritiontreatment

Ultrafine Grain Ferrite Transformed from Fine Austenite Grains Produced by Dynamic Reversal Transformation

Effective grain size refinement of an Fe-24Ni-0.3C metastable austenitic steel by a modified two-step cold rolling and annealing process utilizing the deformation-induced martensitic transformation and its reverse transformation

Micromechanism involved in ultrafine grained ferrite/martensite dual phase steels strengthened by nanoscale Cu-rich precipitates

Control of Upstream Austenite Grain Coarsening during the Thin-Slab Cast Direct-Rolling (TSCDR) Process

Influence of Thermomechanical Control Process on the Evolution of Austenite Grain Size in a Low-Carbon Nb-Ti-Bearing Bainitic Steel

The origin of {113} grains and their impact on secondary recrystallization in producing ultra-thin grain-oriented electrical steel

Preparation of ultrafine-grained Nb-1Zr alloy by increasing the time of large plastic deformation during friction stir processing

Microstructural evolution during the austenite-to-ferrite transformation from deformed austenite

Effect of Dissolved and Precipitated Niobium in Microalloyed Steel on Deformation Induced Ferrite Transformation (Dift)

Grain Refinement and Texture Change in Interstitial Free Steels after Severe Rolling and Ultra-Short Annealing

Refinement mechanism of centimeter-grade coarse grains in as-cast Ti 2 AlNb-based alloy during multi-directional forging

Development of Very Tough Ferritic Stainless Steels by Optimizing the Recrystallized Microstructure

On the Metastable Ferrite Hot Rolling of Low‐Grade Electrical Steels: Its Microstructure, Texture and Low‐Temperature Annealed Structure

Microstructure Refinement via Nucleation of Intragranular Acicular Ferrite Stimulated by Ti-Containing Core–Shell Structured Particles in Low-Carbon Steel

Microstructural evolution and magnetic properties in strip cast non-oriented silicon steel produced by warm rolling

The Netted Ferrite at Grain Boundaries in the Steels with Thermomechanical Processing

Effect of Grain Size and Residual Strain on the Dynamic Transformation of Austenite under Plate Rolling Conditions

Microstructural refinement by the formation of acicular ferrite on Ti–Mg oxide inclusion in low-carbon steel

Facile route to bulk ultrafine-grain steels for high strength and ductility