Abstract:Steels with sub-micrometre grain sizes usually possess high toughness and strength, which makes them promising for lightweighting technologies and energy-saving strategies. So far, the industrial fabrication of ultrafine-grained (UFG) alloys, which generally relies on the manipulation of diffusional phase transformation, has been limited to steels with austenite-to-ferrite transformation<a href="#ref-CR1">1</a>,<a href="#ref-CR2">2</a>,<a href="/articles/s41586-021-03246-3#ref-CR3">3</a>. Moreover, the limited work hardening and uniform elongation of these UFG steels<a href="/articles/s41586-021-03246-3#ref-CR1">1</a>,<a href="/articles/s41586-021-03246-3#ref-CR4">4</a>,<a href="/articles/s41586-021-03246-3#ref-CR5">5</a> hinder their widespread application. Here we report the facile mass production of UFG structures in a typical Fe–22Mn–0.6C twinning-induced plasticity steel by minor Cu alloying and manipulation of the recrystallization process through the intragranular nanoprecipitation (within 30 seconds) of a coherent disordered Cu-rich phase. The rapid and copious nanoprecipitation not only prevents the growth of the freshly recrystallized sub-micrometre grains but also enhances the thermal stability of the obtained UFG structure through the Zener pinning mechanism<a href="/articles/s41586-021-03246-3#ref-CR6">6</a>. Moreover, owing to their full coherency and disordered nature, the precipitates exhibit weak interactions with dislocations under loading. This approach enables the preparation of a fully recrystallized UFG structure with a grain size of 800 ± 400 nanometres without the introduction of detrimental lattice defects such as brittle particles and segregated boundaries. Compared with the steel to which no Cu was added, the yield strength of the UFG structure was doubled to around 710 megapascals, with a uniform ductility of 45 per cent and a tensile strength of around 2,000 megapascals. This grain-refinement concept should be extendable to other alloy systems, and the manufacturing processes can be readily applied to existing industrial production lines.

Effective grain size refinement of an Fe-24Ni-0.3C metastable austenitic steel by a modified two-step cold rolling and annealing process utilizing the deformation-induced martensitic transformation and its reverse transformation

Strain-induced Refinement and Thermal Stability of a Nanocrystalline Steel Produced by Surface Mechanical Attritiontreatment

Tailoring the metastable reversed austenite from metastable Mn-rich carbides

Development of Very Tough Ferritic Stainless Steels by Optimizing the Recrystallized Microstructure

Facile route to bulk ultrafine-grain steels for high strength and ductility

Refinement mechanism of centimeter-grade coarse grains in as-cast Ti 2 AlNb-based alloy during multi-directional forging

Nanoscale austenite reversion through partitioning, segregation, and kinetic freezing: Example of a ductile 2 GPa Fe-Cr-C steel

Micromechanism involved in ultrafine grained ferrite/martensite dual phase steels strengthened by nanoscale Cu-rich precipitates

Microstructure evolution and mechanical properties of metastable austenitic medium Mn steel fabricated by warm caliber rolling

Microstructural evolution during the austenite-to-ferrite transformation from deformed austenite

Tailoring the Microstructure to Enhance the Cryogenic Mechanical Properties of a Fe–34.5mn–0.04c Steel

Formation of Fine Austenite Through Static Recrystallization in Low Carbon Micro-alloyed Steels

Grain Refinement and Texture Change in Interstitial Free Steels after Severe Rolling and Ultra-Short Annealing

Yielding Behavior and Strengthening Mechanisms of a High Strength Ultrafine‐Grained Cr–Mn–Ni–N Stainless Steel

Influence of Thermomechanical Control Process on the Evolution of Austenite Grain Size in a Low-Carbon Nb-Ti-Bearing Bainitic Steel

Microstructural Evolution of Metastable Austenitic Steel During High-Pressure Torsion and Subsequent Heat Treatment

A novel process for simultaneously improving the strength and plasticity of 18Ni(350) maraging steel

On the Metastable Ferrite Hot Rolling of Low‐Grade Electrical Steels: Its Microstructure, Texture and Low‐Temperature Annealed Structure

Microstructural refinement by the formation of acicular ferrite on Ti–Mg oxide inclusion in low-carbon steel

Effect of Cold Rolling and Cryogenic Treatment on the Microstructure and Mechanical Properties of Fe–32Ni Alloy

Structure and mechanical behavior of ultrafine-grained aluminum-iron alloy stabilized by nanoscaled intermetallic particles