Abstract:Effects of temperature, strain, strain rate and cooling rate on austenite grain size were investigated at first. The results show that by increasing the strain from 0.0 to 0.5 can significantly refine austenite grains for different deformation temperatures studied. However, by increasing the strain from 0.5 to 0.8 can not continue to refine austenite grains for higher deformation temperatures of 1 100 and 1150 degrees C, while austenite grains can be further refined for lower deformation temperature of 1 000 degrees C. The austenite grain size is proportional to (epsilon) over dot(-rho) ((epsilon) over dot is strain rate and rho is the strain rate exponent) and v(-q) (v is cooling rate and q is cooling rate exponent). Moreover, using ultra fast cooling after hot rolling can significantly refine austenite grains. Then a low-carbon bainite steel with yield strength of 811 MPa and ductile-brittle transition temperature (DBTT) of -49 degrees C produced by optimum recrystallization controlled rolling designed based on thermosimulation results and ultra fast cooling. The microstructural characteristics, mechanical properties and the mechanism of toughening were investigated in details. On the one hand, fine austenite grains with equivalent diameter of 16.5 mu m is obtained by recrystallization repeated and suppressing recrystallized austenite grain growth using ultra fast cooling. On the other hand, recrystallized austenite grains are divided by fine bainite blocks with higher misorientation between each other. So the fine bainite microstructure is obtained. In addition, Prior austenite grain boundaries and bainite packet and block boundaries with higher misorientation can effectively arrest cracks propagation, resulting in better low-temperature toughness.

Formation of Fine Austenite Through Static Recrystallization in Low Carbon Micro-alloyed Steels

Strain-induced Refinement and Thermal Stability of a Nanocrystalline Steel Produced by Surface Mechanical Attritiontreatment

Control of austenite grain size in a low carbon steel

Static and Metadynamic Recrystallization of Low Carbon Steels During Mechanical Deformation

Grain Refining Behavior by Dynamic Recrystallization of As-Forged Austenitic Stainless Steel with High N

MICROSTRUCTURE REFINEMENT OF DEFORMATION-ENHANCED TRANSFORMATION IN LOW CARBON STEEL

Dynamic recrystallization of ferrite in a low-carbon steel

Dynamic recrystallization of ferrite during deformation at temperatures below A(c1) in a low carbon steel

Mechanisms of Microstructure Evolution During Deformation of Undercooled Austenite in a Low Carbon Steel

Effective grain size refinement of an Fe-24Ni-0.3C metastable austenitic steel by a modified two-step cold rolling and annealing process utilizing the deformation-induced martensitic transformation and its reverse transformation

Recrystallization of ferrite–austenite stainless steel

The Dynamic Recovery and Recrystallization for Ultrafine Grained Low Alloyed Steel

Dynamic Recrystallization of Hot Deformed Austenite for Microalloyed Bainitic Engineering Steel

Low-Carbon Bainite Steel with High Strength and Toughness Processed by Recrystallization Controlled Rolling and Ultra Fast Cooling (RCR+UFC)

Ultra-fine ferrite formation during deformation of undercooled austenite in a low carbon steel

Recrystallisation-assisted creep of an austenitic Fe-Ni alloy under low stresses after hot deformation

Study on dynamic recrystallization of ultra-high strength 22MnB5 steel during hot rolling

Titanium‐Dependent Kinetics of Ferrite Single‐Phase Recrystallization in Cold‐Rolled Ultra‐High‐Strength Low‐Alloy Steels During Annealing

Dynamic Recrystallization of Austenite and Grain Refinement in 40cr Steel

Research on Dynamic Recrystallization of the Microalloyed Forging Steels

Effect of Deformation and Cooling Rate on the Transformation Behavior and Microstructure of X70 Steels