Abstract:Microfluidics, as an emerging technology, is highly dependent on the evolution of device materials and fabrication techniques. While replica molding of polydimethylsiloxane and hot embossing/injection molding of thermoplastics are most popular, they are either hard to scale up or inappropriate for laboratory-scale prototyping. Recently, photocurable resins, as a huge class of materials, have attracted extensive interest. However, very few of them can now be used in device fabrication due to the challenge in machining these materials. In response, we herein propose a novel concept of composite elastomers, which can covalently link with and consequently offer a flexible support to photocured thin films. This effect would allow most photocurable resins to be used in microfluidic device fabrication, greatly enriching the material choices for diverse applications. Moreover, the whole fabrication process becomes very simple and rapid, with an impressive throughput of at least hundreds of replicas per day. With these features, it is reasonably expected that the composite elastomer-enabled rapid photofabrication method will be very competent for laboratory prototyping, providing not only the ease of fabrication but also a possibility to select the materials specifically for ultimate applications and promising potential for volume production without the redevelopment process. These may offer a good opportunity to narrow the current gap between academic research and industrial practice.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c06143.Movies showing the flexibility of the composite elastomer, process of composite elastomer-enabled photofabrication of the microfluidic device, generation of W/O/W double emulsion droplets, and operation of Quake valves (MP4, MP4, MP4, MP4)This article has not yet been cited by other publications.

Rapid Prototyping of Poly(methyl Methacrylate) Microfluidic Systems Using Solvent Imprinting and Bonding.

Rapid Prototyping of Soft Lithography Masters for Microfluidic Devices Using Dry Film Photoresist in a Non-Cleanroom Setting

Fabrication of Fluidic Chips with 1-D Nanochannels on PMMA Substrates by Photoresist-Free UV-lithography and UV-assisted Low-Temperature Bonding

A Polymeric Master Replication Technology for Mass Fabrication of Poly(dimethylsiloxane) Microfluidic Devices.

Rapid prototyping of micro/nano poly (methyl methacrylate) fluidic systems using proton beam writing

Poly(methyl Methacrylate) CE Microchips Replicated from Poly(dimethylsiloxane) Templates for the Determination of Cations

Fabrication of a Three-Dimensional Microfluidic System from Poly(methyl methacrylate) (PMMA) Using an Intermiscibility Vacuum Bonding Technique

Miscible Organic Solvents Soak Bonding Method Use in a PMMA Multilayer Microfluidic Device.

Fabrication of 1-d nanochannels on PMMA substrate by photoresist-free uv lithography and UV-assisted bonding under low temperature

Rapid prototyping of PMMA-based microfluidic spheroid-on-a-chip models using micromilling and vapour-assisted thermal bonding

Fused Deposition Modeling of Microfluidic Chips in Polymethylmethacrylate

Rapid Fabrication Of Poly(Methyl Methacrylate) Capillary Electrophoresis Microchips By In Situ Surface Polymerization

Fabrication of Micro Pneumatic Valves with Double-Layer Elastic Poly(dimethylsiloxane) Membranes in Rigid Poly(methyl Methacrylate) Microfluidic Chips

Low-cost Fabrication of Poly(methyl Methacrylate) Microchips Using Disposable Gelatin Gel Templates.

A Rapid Prototyping Approach for Multi-Material, Reversibly Sealed Microfluidics

Fabrication of poly(methyl methacrylate) microfluidic chips by redox-initiated polymerization.

Fabrication of Poly(methyl Methacrylate)(pmma) Microfluidic Chips by a Simple Hot Embossing Method

Composite Elastomer-Enabled Rapid Photofabrication of Microfluidic Devices

Rapid Prototyping of Multi-Functional and Biocompatible Parafilm®-Based Microfluidic Devices by Laser Ablation and Thermal Bonding

Solvent Bonding of Poly(methyl Methacrylate) Microfluidic Chip Using Phase‐changing Agar Hydrogel As a Sacrificial Layer

Fabrication of poly(methyl methacrylate) capillary electrophoresis microchips by in situ surface polymerization.