Abstract:A simple and highly selective flow injection on-line pre-concentration and separation-flame atomic absorption spectrometric method was developed for routine analysis of trace amounts of lead in biological and environmental samples. The selective preconcentration of lead was achieved in a wide range of sample acidity (0.075 to > or = 3 mol L(-1)HNO3) on a microcolumn (145 microL) packed with a macrocycle immobilized on silica gel. The lead retained on the column was effectively eluted with an EDTA solution (0.03 mol L(-1), pH 10.5). Three kinds of potential interferences, i.e., preconcentration inferences from metal ions with an ionic radius similar to that of Pb(II) due to their competition for the cavity of the macrocyle, elution kinetic interferences from ions which form stable complexes with EDTA due to their competition for EDTA, and interferences in the atomizer from residual matrix, were evaluated and compared in view of the read-out mode of the analyte response (peak area vs peak height), column wash step (with vs without), column capacity (50 vs 145 microL), and column shape (conical vs cylindrical). The results showed that a combination of increase in column capacity, quantitation based on peak area, and use of dilute nitric acid for column wash before elution efficiently avoid the above-mentioned potential interferences. With the use of a 145 microL column the present system tolerated up to 0.1 g L(-1) Ba(II), 1 g L(-1) Sr(II), and at least 10 g L(-1) Fe(III), Cu(II), Ni(II), Zn(II), Cd(II), Al(III), K(I), Na(I), CaII), and Mg(II) in the sample digest. Further improvement of the interference tolerance can be achieved by increasing column capacity if more complicated samples need to be analyzed. At a sample loading rate of 3.9 mL min(-1) with 30-s preconcentration, an enrichment factor of 52, a detection limit (3s) of 5 micrograms L(-1) Pb in the digest and a sampling frequency of 63 h(-1) were obtained. The precision (RSD, n = 11) at the 200 micrograms L(-1) level was 1.9%. The enrichment factor and the detection limit can be further improved by increasing sample loading rate without degradation in the efficiency due to the favorable kinetics and low hydrodynamic impedance of the present system. The analytical results obtained by the proposed method for a number of biological and environmental standard reference materials were in good agreement with the certified and recommended values.

Sequential/bead Injection Lab-on-valve Incorporating a Renewable Microcolumn for Co-Precipitate Preconcentration of Cadmium Coupled to Hydride Generation Atomic Fluorescence Spectrometry

Octadecyl immobilized surface for precipitate collection with a renewable microcolumn in a lab-on-valve coupled to an electrothermal atomic absorption spectrometer for ultratrace cadmium determination.

A Sequential Injection On-Line Column Preconcentration System for Determination of Cadmium by Electrothermal Atomic Absorption Spectrometry

Integrating preconcentration, tetrahydroborate immobilization, elution and chemical vapor generation onto a cellulose surface for the determination of cadmium with atomic fluorescence spectrometry

An Octadecyl Immobilized Silica Beads Packed Microcolumn Versus Polytetrafluoroethylene Knotted Reactor for Cd(Oh)(2) Precipitate Collection Coupled to Electrothermal Atomic Absorption Spectrometry for Cadmium Screening

Sequential Injection–bead Injection–lab-on-valve Schemes for On-Line Solid Phase Extraction and Preconcentration of Ultra-Trace Levels of Heavy Metals with Determination by Electrothermal Atomic Absorption Spectrometry and Inductively Coupled Plasma Mass Spectrometry

Biological cell-sorption for separation/preconcentration of ultra-trace cadmium in a sequential injection system with detection by electrothermal atomic absorption spectrometry

On-Line Ion Exchange Preconcentration in A Sequential Injection Lab-On-Valve Microsystem Incorporating A Renewable Column with Etaas for the Trace Level Determination Bismuth in Urine River Sediment

Flow injection hydride generation and on-line W-coil trapping for electrothermal vaporization dielectric barrier discharge atomic emission spectrometric determination of trace cadmium

Octadecyl immobilized silica beads packed microcolumn versus PTFE knotted reactor as Cd(OH)2 precipitate collection media coupled to ETAAS for cadmium determination

Flow Injection On-Line Coprecipitation Preconcentration for Electrothermal Atomic Absorption Spectrometry

Development of a miniature analytical system in a lab-on-valve for determination of trace copper by bead injection spectroscopy.

Application of a macrocycle immobilized silica gel sorbent to flow injection on-line microcolumn preconcentration and separation coupled with flame atomic absorption spectrometry for interference-free determination of trace lead in biological and environmental samples

On-line separation and preconcentration of trace cadmium in environmental water samples by micro column filled with modified nanometer Si-HAP prior to FAAS determination

Flow injection on-line solid phase extraction for ultra-trace lead screening with hydride generation atomic fluorescence spectrometry.

Combination of Knotted Reactor with Portable Tungsten Coil Electrothermal Atomic Absorption Spectrometer for On-Line Determination of Trace Cadmium

Flow Injection On-Line Separation and Preconcentration for Electrothermal Atomic Absorption Spectrometry. Part 1. Determination of Ultratrace Amounts of Cadmium, Copper, Lead and Nickel in Water Samples

Flow Injection Hydride Generation for On-Atomizer Trapping: Highly Sensitive Determination of Cadmium by Tungsten Coil Atomic Absorption Spectrometry

A miniature optical emission spectrometric system in a lab-on-valve for sensitive determination of cadmium.

Simultaneous flow injection preconcentration of lead and cadmium using cloud point extraction and determination by atomic absorption spectrometry