Abstract:A Co-Ni-Cu multiprincipal element alloy (MPEA) powder was successfully synthesized through coprecipitation. Results of energy dispersive spectroscopy (EDS) and X-ray fluorescence spectroscopy (XRF) revealed nearly equal atomic ratios for Co, Ni, and Cu in the Co-Ni-Cu MPEA powder. Moreover, X-ray diffraction (XRD) confirmed a single-phase face-centered cubic (fcc) structure in the Co-Ni-Cu MPEA powder. To explore the differences in microstructure and mechanical properties, we compared a novel WC-2Co-2Ni-2Cu cemented carbide, utilizing the Co-Ni-Cu MPEA as a binder, with conventional WC-6Co and WC-3Co-3Ni cemented carbides prepared via liquid phase sintering. This comparison was conducted using scanning electron microscopy, XRD, and mechanical properties testing. Observations revealed that the surfaces of WC grains in WC-2Co-2Ni-2Cu and WC-6Co appeared smooth and flat, while those in WC-3Co-3Ni exhibited roughness with numerous terraces. In addition, the average grain size was 0.96, 1.14, and 1.22 mu m in WC-2Co-2Ni-2Cu, WC-6Co, and WC-3Co-3Ni, respectively. Notably, the Co-Ni-Cu MPEA inhibited WC grain growth. WC-2Co-2Ni-2Cu (1388 HV30) exhibited hardness similar to that of WC-6Co (1406 HV30) but the highest fracture toughness (9.04 MPa center dot m(1/2)), while WC-3Co-3Ni (1332 HV30) presented the lowest hardness. Bending strength values were recorded at 2406 MPa for WC-2Co-2Ni-2Cu, 2816 MPa for WC-6Co, and 2645 MPa for WC-3Co-3Ni, with WC-6Co exhibiting the highest bending strength. Considering their microstructures, physical properties, and mechanical properties comprehensively, the novel cemented carbides exhibited only slightly reduced bending strength compared to conventional counterparts. Thus, the Co-Ni-Cu MPEA binder demonstrates promising potential as a replacement for the conventional Co metal binder.

Comparative research on properties of four kinds of wax binder for cemented carbide

Designing on New Binders for Ultrafine Cemented Carbide Bar Extrusion Molding

Research on pre-debinding process of binders for ultrafine cemented carbide bar extrusion molding

Sintering Process of Extruded Cemented Carbide Rod Prepared with New Binder

Effects of Different Backbone Binders on the Characteristics of Zirconia Parts Using Wax-Based Binder System Via Ceramic Injection Molding

The effect of binder phase content on WC-AlCoCrFeNiTi0.2 high entropy cemented carbides microstructure and mechanical properties

Study On Properties And Effects Of A New Heat Cured Inorganic Foundry Binder

The Effect of Carbon Content on the Microstructure and Mechanical Properties of Cemented Carbides with a CoNiFeCr High Entropy Alloy Binder

Study on Effect of High-Entropy Alloy Binder on Microstructure and Properties of WC Cemented Carbide Doped with Rare Earth Oxide

Insight into Grain Refinement Mechanisms of WC Cemented Carbide with Al0.5CoCrFeNiTi0.5 Binder

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

A thermal-initiated monomer binder enhancing green strength with low binder saturation for binder jetting additive manufacturing of cemented carbide

Evaluation on Died-Pressed Binders of Ti(C,N)-Based Cermet Powders

Microstructures and Properties of a Novel Cemented Carbide Prepared Using a Co–Ni–Cu Multiprincipal Element Alloy As the Binder

Powder Modification Mechanism, Effects of Binder Compositions on the Thermal Behavior, and the Mechanical Properties of the Ceramic Injection Molded System

Effects of the Binder Compositions on the Homogeneity of Ceramic Injection Molded Compacts

Effect of binder content and sintering time on the microstructure and mechanical properties of gradient cemented carbides with Ni binder

Superiority of a New Modified Phosphate Casting Binder

Binary Binder for Cf/C-SiC Composites with Enhanced Mechanical Property

Boosting the collapse performance of Wax-binder-free silica based ceramic core via adding nano-alumina sol modified fused silica powder

Microstructure and properties of WC-Co/CrMnFeCoNi composite cemented carbides