Abstract:Abstract The machining of thin-wall components made of titanium alloys is challenging because the poor machinability of the material leads to severe problems such as accelerated tool wear and poor surface quality, while the weak rigidity of the thin-wall structure results in unavoidable vibration and surface form errors. To address these issues, this paper investigated the mechanisms and performance of cooling minimum quantity lubrication (CMQL) in milling titanium thin-wall parts. To verify the efficiency of CMQL, different cooling/lubrication strategies, including conventional flood cooling, minimum quantity lubrication (MQL) and CMQL with different temperature levels, were investigated. The cutting force, tool wear state, chip formation, surface integrity, and surface form errors were compared and analysed in detail. The experiment results show that MQL is inadequate at higher spindle speeds due to its ineffective cooling capacity and weakened lubrication ability. In contrast, CMQL has demonstrated its feasibility and superiority in milling titanium thin-wall parts under all conditions. The outcomes indicate that a lower temperature level of CMQL is advantageous to producing better wear resistance and lower thermomechanical loads, and the CMQL (− 15 oC) machining environment can remarkably improve the overall machining performance and control the surface form errors of the machined thin-wall parts. At the spindle speed of 3000 rpm, the surface roughness measured under CMQL (− 15 °C) condition is reduced by 16.53% and 23.46%, the deflection value is decreased by 54.74% and 36.99%, while the maximum thickness error is about 53.51% and 20.56% smaller in comparison to flood cooling and MQL machining. In addition, CMQL is an economical and sustainable cooling/lubrication strategy; the outcomes of this work can provide the industry with useful guidance for high-quality machining of thin-wall components.

Effect of Cutting Parameters on Minimum Quantity Lubrication Machining of High Strength Steel

Influence of Minimum Quantity Lubrication Parameters on Tool Wear and Surface Roughness in Milling of Forged Steel

High-Speed Milling of Hardened Mold Steel P20 with Minimum Quantity Lubrication

Optimization of Technological Parameters and Application Conditions of CMQL in High-Speed Milling 300M Steel

The Effects of Minimum Quantity Lubrication (MQL) on Machining Force, Temperature, and Residual Stress

Effect of Cryogenic Minimum Quantity Lubrication on Machinability of Diamond Tool in Ultraprecision Turning of 3cr2nimo Steel

The effects of minimum quantity lubrication parameters on the lubrication efficiency in the turning of plastic mold steel

Selection of Minimum Quantity Lubrication (MQL) Parameters in Milling of Ti-6Al-4V

Investigation Of Cutting Force And Temperature Of End-Milling Ti-6al-4v With Different Minimum Quantity Lubrication (Mql) Parameters

Investigation of Machinability in Minimum Quantity Lubrication Milling of Gh4169 Aerospace Superalloy

Examination of Minimum Quantity Lubrication Performance in the Hard Turning of AISI/SAE 1060 High-Carbon Steel

Experimental Study on Micro-Milling of Ti6Al4V with Minimum Quantity Lubrication

Investigation on Surface Grinding of Ti-6Al-4V Using Minimum Quantity Lubrication

Evaluation of minimum quantity lubrication effects by cutting force signals in face milling of Inconel 182 overlays

An Experimental Investigation on Effects of Minimum Quantity Lubrication Oil Supply Rate in High-Speed End Milling of Ti–6Al–4V

Investigation of Grinding Ti-6al-4v under Minimum Quantity Lubrication (mql) Condition

Investigation of friction in end-milling of Ti-6Al-4V under different green cutting conditions

Effects of cooling air temperature on cryogenic machining of Ti–6Al–4V alloy

Machinability Assessment of Hybrid Nano Cutting Oil for Minimum Quantity Lubrication (MQL) in Hard Turning of 90CrSi Steel

The machinability of titanium alloy thin-wall parts in cooling minimum quantity lubrication (CMQL) environments

Effect of Minimum Quantity of Lubricant on Carbide Tools and Surface Integrity in the Machining of Titanium Aluminides