Abstract:Highlights • Superplasticity of fine-grained Mg-10Li alloy was studied. • Severe plastic deformation was used to achieve the fine grains. • Its deformation mechanisms for superplastic flow were analyzed. • Deformation mechanism maps were constructed in 2D and 3D. The superplastic behavior and associated deformation mechanisms of a fine-grained Mg-10.1 Li-0.8Al-0.6Zn alloy (LAZ1011) with a grain size of 3.2 μm, primarily composed of the BCC β phase and a small amount of the HCP α phase, were examined in a temperature range of 473 K to 623 K. The microstructural refinement of this alloy was achieved by employing high-ratio differential speed rolling. The best superplasticity was achieved at 523 K and at strain rates of 10 −4 -5 × 10 −4 s −1 , where tensile elongations of 550–600% were obtained. During the heating and holding stage of the tensile samples prior to tensile loading, a significant increase in grain size was observed at temperatures above 573 K. Therefore, it was important to consider this effect when analyzing and understanding the superplastic deformation behavior and mechanisms. In the investigated strain rate range, the superplastic flow at low strain rates was governed by lattice diffusion-controlled grain boundary sliding, while at high strain rates, lattice diffusion-controlled dislocation climb creep was the rate-controlling deformation mechanism. It was concluded that solute drag creep is unlikely to occur. During the late stages of deformation at 523 K, it was observed that grain boundary sliding led to the agglomeration of the α phase, resulting in significant strain hardening. Deformation mechanism maps were constructed for β-Mg-Li alloys in the form of 2D and 3D formats as a function of strain rate, stress, temperature, and grain size, using the constitutive equations for various deformation mechanisms derived based on the data of the current tests.

Superplasticity in Mg–Li–Zn Alloys Processed by High Ratio Extrusion

Introducing Equiaxed Grains and Texture into Ni-Mn-Ga Alloys by Hot Extrusion for Superplasticity

On Mechanical Properties and Superplasticity of Mg–15Al–1Zn Alloys Processed by Reciprocating Extrusion

Superplasticity of fine-grained Mg-10Li alloy prepared by severe plastic deformation and understanding its deformation mechanisms

High Strain Rate Quasi-Superplasticity Behavior in an Ultralight Mg-9.55Li-2.92Al-0.027Y-0.026Mn Alloy Fabricated by Multidirectional Forging and Asymmetrical Rolling

Superplasticity of 5083 Alloys with Zr and Mn Additions Produced by Reciprocating Extrusion

Deformation-induced Dynamic Precipitation of 14H-LPSO Structure and Its Effect on Dynamic Recrystallization in Hot-Extruded Mg-Y-Zn Alloys

High Strain Rate Superplasticity in Al-Zn-Mg-Based Alloy: Microstructural Design, Deformation Behavior, and Modeling

Enhanced superplasticity achieved by disclination-dislocation reactions in a fine-grained low-alloyed magnesium system

Realizing impressive superplasticity in a low-alloyed Mg-Zn-Ca-Al-Mn alloy: The roles of grain boundary segregation and dense β-Mn particles

Numerical and Experimental Investigation on Hot Backward Extrusion Process of Mg-Gd-Y-Zn-Zr Magnesium Alloy

Achieving high strain rate superplasticity in an Al-Cu-Li alloy processed by thermo-mechanical processing

Microstructural evolution and superplasticity of Al-5.8Mg-0.23Mn alloys processed by reciprocating extrusion

The abnormal flow behavior of Mg-9Gd-4Y-2Zn-0.5Zr alloy during hot tensile deformation at high temperature and low strain rate

High-temperature superplastic behavior and ECAP deformation mechanism of two-phase Mg-Li alloy

Revealing the dynamic recrystallization mechanism, extrusion deformation mechanism, and tensile deformation behavior of Mg–6Al–1Zn–1.1Sc alloy

Microstructures, hot tensile deformation behavior and constitutive modeling in a superlight Mg-2.76Li-3Al-2.6Zn-0.39Y alloy

An Mg‐Al‐Zn Alloy with Verry High Specific Strength and Superior High‐strain‐rate Superplasticity Processed by Reciprocating Extrusion

Room-Temperature Superplasticity in an Ultrafine-Grained Magnesium Alloy

Study on Thermal Compression Deformation Behavior and Constitutive Model of Homogenized Mg–5Zn–1Mn Alloy

In-situ surface study on the mechanism of high-strain-rate superplasticity in an Al–Cu–Li alloy