Abstract:In this study, equal channel angular pressing (ECAP) was applied to a hot-extruded Mg–5.00Zn–0.92Y–0.16Zr (wt.%) alloy to produce an ultrafine-grained a-Mg structure of 0.6μm with uniformly distributed fine quasicrystal Mg3YZn6 particles. The basal planes in the as-ECAPed alloy were inclined approximately 45° to the ECAP direction (EPD); thus, a high Schmid factor of 0.36 for (0001)〈112¯0〉 basal slip along EPD was obtained. Then, the superplastic behavior at low temperatures of 150–250°C and initial strain rates of 1.67×10−3s−1–1.67×10−1s−1 of the as-ECAPed alloy was investigated and compared with that of the as-extruded alloy. The microstructural development, texture evolution and cracking behavior during tensile tests were systemically investigated by electron backscattered diffraction (EBSD) analysis. During the tensile test along the EPD, the basal planes in the as-ECAPed alloy specimen were tilted approximately 15° away from the original position; thus, the basal planes were still in a position favorable for the basal slip along the EPD. As a result, a maximum elongation of 865% was obtained at 200°C and a strain rate of 1.67×10−3s−1, as a result of this favored basal texture and the excellent thermal stability of the ultrafine-grained structure. This optimum superplastic temperature of 200°C is much lower than that obtained for other Mg–Zn–Y–(Zr) alloys. In contrast, for the as-extruded alloy specimen, superplastic behavior did not occur until the critical condition of 250°C and a strain rate of 1.67×10−3s−1. Below this temperature and strain rate, the strong extrusion basal texture was maintained, and the cracks in the hot-worked coarse region (or un-DRXed region) were observed nucleating mainly associated with the formation of a 38° {101¯1}–{101¯2} double twin. At this temperature and strain rate, the hot-worked coarse regions were significantly refined by the dynamic recovery and the following recrystallization process. In the case, the formation of a double twin was prevented and the facture was delayed.

High-temperature superplastic behavior and ECAP deformation mechanism of two-phase Mg-Li alloy

Superplasticity of fine-grained Mg-10Li alloy prepared by severe plastic deformation and understanding its deformation mechanisms

Microstructure and Mechanical Properties of a Two‐Phase Mg–Li Alloy Processed By Constrained Groove Pressing

Prominent role of multi-scale microstructural heterogeneities on superplastic deformation of a high solid solution Al–7Mg alloy

Superplastic Behavior of an Al–Mg–Li Alloy

Superplastic Behavior and Microstructural Evolution in a Commercial Mg-3Al-1Zn Magnesium Alloy.

Plastic Deformation Behavior Of Mg-Li Alloys At Ambient And Elevated Temperatures

Superplastic behavior and microstructural evolution in a commercial Mg-3Al-1Zn magnesium alloy : Superplasticity and its applications

High Strain Rate Quasi-Superplasticity Behavior in an Ultralight Mg-9.55Li-2.92Al-0.027Y-0.026Mn Alloy Fabricated by Multidirectional Forging and Asymmetrical Rolling

Microscopic and Mesoscopic Deformation Behaviors of Dual-Phase Mg-Li-Gd Alloys

Deformation behavior and phase transformation of a dual-phase Mg−8.9Li−2.7Al-0.85Si alloy under compression test at elevated temperatures

On Mechanical Properties and Superplasticity of Mg–15Al–1Zn Alloys Processed by Reciprocating Extrusion

High Strain Rates Deformation Behavior of an As-Extruded Mg–2.5Zn–4Y Magnesium Alloy Containing LPSO Phase at High Temperatures

Room-Temperature Superplasticity in an Ultrafine-Grained Magnesium Alloy

Superplastic Deformation Mechanisms of Coarse-Grained Rolled Mg-4Y-3RE Magnesium Alloy

The Microstructural Evolution and Superplastic Behavior at Low Temperatures of Mg–5.00Zn–0.92Y–0.16Zr (wt.%) Alloys after Hot Extrusion and ECAP Process

Realizing impressive superplasticity in a low-alloyed Mg-Zn-Ca-Al-Mn alloy: The roles of grain boundary segregation and dense β-Mn particles

Achieving high strain rate superplasticity in an Al-Cu-Li alloy processed by thermo-mechanical processing

In-situ surface study on the mechanism of high-strain-rate superplasticity in an Al–Cu–Li alloy

Superplastic Behavior and Microstructure Evolution of a Fine-Grained Mg-Nd-Zn-Zr Alloy Processed by Hot Extrusion

Microstructures, hot tensile deformation behavior and constitutive modeling in a superlight Mg-2.76Li-3Al-2.6Zn-0.39Y alloy